In push mode we process as much as possible in the adapter. When we receive
a DISCONT buffer which we can't match to an actual sample (based on the existing
sample table) and there is still data remaining in the incoming adapter,there is
one of two cases happening:
1) We are doing reverse playback, in which case we should flush out all pending
data
2) We have leftover data from the previous incoming buffer... which we can't do
anything about.
For the second case, make sure we flush out the remaining data so that we can start
parsing again from scratch.
https://bugzilla.gnome.org/show_bug.cgi?id=781319
They should have ideally the same timescale of the video track, which we
can't guarantee here as in theory timecode configuration and video
framerate could be different. However we should set a correct timescale
based on the framerate given in the timecode configuration, and not just
use the framerate numerator.
Make sure offset and neededbytes are properly resetted when all
streams are EOS in push-mode.
Avoids cases when some data might still be pushed by upstream (because
it didn't yet see the resulting GST_FLOW_EOS yet) and qtdemux gets
completely lost.
https://bugzilla.gnome.org/show_bug.cgi?id=781266
buf is the current pad->last_buf value. If ever it gets copied/unreffed,
we need to make sure to write back the new pointer to the last_buf
variable.
Fixes using wrong pointer values in the case of decrasing DTS value
Before pushing a sample, check if there was a change in the current
stsd entry. This patch also assumes that the first stsd entry is
used as default for the first sample. It might cause an uneeded
caps renegotiation when this isn't the case.
stsd can have multiple format entries, parse them all.
This is required to play DVB DASH profile that uses multiple entries
to identify the different available bitrates/options on dash streams
The stream format-specific data is not stored into QtDemuxStreamStsdEntry
Instead of using the stsd as a base pointer, use the actual stsd
entry as the stsd can have multiple entries. This is rarely used
for file playback but is a possible profile with in DVB DASH specs.
This still doesn't support stsd with multiple entries but makes it
easier to do so.
AudioSpecifigConfig is used in a variety of AAC streams but was
being parsed differently. Instead, make everyone use the same parsing.
* Remove unused 'bits' field (it was always set to 0 if present)
* Add proper GAConfig parsing (to know the number of samples per frame
if present).
Fixes wrong rate/channels configuration in streams coming from qtdemux
https://bugzilla.gnome.org/show_bug.cgi?id=780966
According to ISO/IEC:14496-2:2009 , in the case of HE-AACv2 (audioObjecType
29) parametric stereo is used (a single mono track is used and then
transformations are applied to it to provide a stereo output).
We therefore report two channels in the case where there is one reported
in the audioChannelConfiguration.
Fixes the various issues where a demuxer would report two channels, but
then the parser would say there's only one channel, and then the decoder
would output two channels.
last_buf is the one we're going to write next, not buf. As such we
should check timestamps against that one if there is one to select the
earliest pad.
Also remember the currently selected pad in the very beginning when
storing the first last_buf.
This both solves some edge cases where not the correct next pad was
selected corresponding to the target interleave.
This is an update of d78d589627
We still exit as early as possible in case of non-ok/non-unlinked combined
flow, but we first make sure that we update the internal position variables.
This ensures that if upstreams "ignores" the flow return (and carries on pushing),
we don't end up processing data with completely bogus variables/positions.
If self->channel_positions == NULL (which seems unlikely),
self->default_channels_ordering_map will be used unintialised.
We avoid that by keeping track of the channel_mask, which is set when
the ordering map is initialised.
https://bugzilla.gnome.org/show_bug.cgi?id=780331
When there are more than 64 channels, we don't want to exceed the
bounds of the ordering_map buffer, and in these cases we don't want to
rempa at all. Here we avoid doing that.
https://bugzilla.gnome.org/show_bug.cgi?id=780331
TFDTs with time 0 are being ignored since commit 1fc3d42f. They're
mistaken with the case of not having TFDT, but those two cases
must be distinguished in some way.
This patch passes an extra boolean flag when the TFDT is present.
This is now the condition being evaluated, instead of checking for
0 time.
https://bugzilla.gnome.org/show_bug.cgi?id=780410
If we have multiple tracks with timecodes, or it's not the first track
that has timecodes, or not the first buffer, we already started a chunk
for media data. We now need to "close" that chunk because we wrote data
for the timecode track and a new chunk has to be started for the
original track the next time it has data.
Similar to what was done in adaptivedemux, ignore seek
events we've already handled - such as when they are received
on every srcpad of files with lots of streams.
Otherwise mdatleft will have a value calculated from the initial
mdatsize minus the parts of the stream that we saw, which is not
including all the parts of the stream that might've been skipped.
This breaks gst-validate on the build server (though not locally),
and a unit test, and I can't run unit tests right now for some
unrelated reason.
This reverts commit 0747b56f8e.
This debug statement is meant to print the time since the last (early)
RTCP transmission, not the last regular RTCP transmission (which also
happens to be set a few lines above to current_time, so the debug output
is just confusing)
Take into account the atoms at the end of the 'trak' atom when
recovering it. So that its size (already computed and added in the trak
size) isn't making offsets wrong.
https://bugzilla.gnome.org/show_bug.cgi?id=771478
