The PAT is related to the stream, we therefore want it cleared along
with anything stream related.
This commented section was from the (old) mpegtsparse and *might* have
been related to speeding up DVB start-up. But we have another plan for that.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=724716
This allows:
* Better duration estimation
* More accurate PCR location
* Overall more accurate running-time location and calculation
Location and values of PCR are recorded in groups (PCROffsetGroup)
with notable PCR/Offset observations in them (when bitrate changed
for example). PCR and offset are stored as 32bit values to
reduce memory usage (they are differences against that group's
first_{pcr|offset}.
Those groups each contain a global PCR offset (pcr_offset) which
indicates how far in the stream that group is.
Whenever new PCR values are observed, we store them in a sliding
window estimator (PCROffsetGroupCurrent).
When a reset/wrapover/gap is detected, we close the current group with
current values and start a new one (the pcr_offset of that new group
is also calculated).
When a notable change in bitrate is observed (+/- 10%), we record
new values in the current group. This is a compromise between
storing all PCR/offset observations and none, while at the same time
providing better information for running-time<=>offset calculation
in VBR streams.
Whenever a new non-contiguous group is start (due to seeking for example)
we re-evaluate the pcr_offset of each groups. This allows detecting as
quickly as possible PCR wrapover/reset.
When wanting to find the offset of a certain running-time, one can
iterate the groups by looking at the pcr_offset (which in essence *is*
the running-time of that group in the overall stream).
Once a group (or neighbouring groups if the running-time is between two
groups) is found, once can use the recorded values to find the most
accurate offset.
Right now this code is only used in pull-mode , but could also
be activated later on for any seekable stream, like live timeshift
with queue2.
Future improvements:
* some heuristics to "compress" the stored values in groups so as to keep
the memory usage down while still keeping a decent amount of notable
points.
* After a seek compare expected and obtained PCR/Offset and if the
difference is too big, re-calculate position with newly observed
values and seek to that more accurate position.
Note that this code will *not* provide keyframe-accurate seeking, but
will allow a much more accurate PCR/running-time/offset location on
any random stream.
For past (observed) values it will be as accurate as can be.
For future values it will be better than the current situation.
Finally the more you seek, the more accurate your positioning will be.
* Avoids handling twice the same seek (can happen with playbin and files
with subtitles)
* Set the sequence number of the segment event to the sequence number of
the seek event that generated it (-1 for the initial one).
We had two issues with the previous code:
1) We were badly handling PUSI-flagged packets. We were discarding the
initial data (if pointer != 0) whereas we should have been accumulating
it with the previous data (if there was a continuity of course).
=> First series of information loss
2) We were not checking whether there were more sections after the end
of one (i.e. when the following byte was not a stuff byte).
This fixes those two issues.
Fixes#677443https://bugzilla.gnome.org/show_bug.cgi?id=677443
Until now we simply ignored those streams (since we couldn't do anything
with it anyway). Now that we have the mpegts library and we offload the
section handling to the application side we can properly identify and
extract them.
By default it is disabled for tsparse and enabled for tsdemux, but there is
a property to change that.
This should open the way to properly handle all private section streams,
including:
* DSM-CC
* MHEG
* Carousel data
* Metadata streams (though I haven't seen any of those in the wild)
* ... And all other specs/protocols making use of those
Partially fixes#560631
Since we now send all sections to the packetizer, we no longer need to do
anymore in-depth checks for the validity of a section.
The choice boils down to:
1) Is it from a known PES pid ? If so pass it on (which might be just pushing
downstream in the case of tsparse, or accumulating PES data for tsdemux)
2) Is it from a known SI pid ? If so pass it to the section packetizer
* Only mpeg-ts section packetization remains.
* Improve code to detect duplicated sections as early as possible
* Add FIXME for various issues that need fixing (but are not regressions)
https://bugzilla.gnome.org/show_bug.cgi?id=702724
We use add_stream(stream_type:-1) to ensure a programs' PCR Stream is
also taken into account. For most programs this will re-use an
existing ES stream.
So only warn that we are re-adding a stream if it was already present
AND it is not to ensure the PCR stream is taken into account.
First send stream-start, then caps, then segment.
The segment we push is from upstream in push-mode. If we work in pull-mode
then we initialize the base segment to BYTES.
https://bugzilla.gnome.org/show_bug.cgi?id=702422
Ensure the chain is not running before reset the state to avoid race
conditions and random corruptions downstream.
Also fixes segfaults in the packetizer due wrong available values that
causes gst_adapter_map to return a NULL pointer.
This reverts commit e14e310f71.
Would be better move the packetizer flushing to FLUSH_STOP and avoid
the race that way. Without introducing a memory barrier that could
have impact in the performance.
When dealing with non-time based push-mode streams, we need to revert
to using the offset-based PCR/PTS estimation logic of packetizer.
This solves uses cases such as:
pushfile:// ! tsdemux
src ! queue ! tsdemux
https://bugzilla.gnome.org/show_bug.cgi?id=687178
This can be used to notify subclasses no more data is expected this
round.
tsparse will use it to push whole buffers (without copy) on the main
source pad.
It could also be used later to decide whether to push pending data
in order to reduce latency.
