Whenever demux got moov, demux will create new stream. Only exception is
duplicated track-id in a moov box. In that case the first stream
will be accepted. This patch is pre-work for rework of moov handling.
https://bugzilla.gnome.org/show_bug.cgi?id=684790
Corrupted files could potentially have multiple cdat/cdt2 atoms in
a sample entry, which is unclear how to handle.
Ignore repeated ones.
CID #1434162
CID #1434159
The value stored in cenc_aux_sample_count wasn't in sync with the
parsing code that followed which checks whether all entries are
valid and present.
Only write the actual sample count when we know for sure.
CID #1427087
The samples table is sorted by DTS, not PTS. As such we can only get the
correct result when using a binary search on it, if we search for the
DTS.
Also if we only ever search for the frame, where the following frame is
the first one with a PTS after the search position, we will generally
stop searching too early if frames are reordered.
In forwards playback this is not really a problem (after the decoder
reordered the frames, clipping is happening), in reverse playback
it means that we can output one or more frames too few as we stop too
early and the decoder would never receive it.
https://bugzilla.gnome.org/show_bug.cgi?id=782118
If we saw empty segments, we previously unconditionally pushed a
GAP event downstream regardless of the duration of that empty
segment.
In order to avoid issues with initial negotiation of downstream elements
(which would negotiate to something before receiving any data due to
that initial GAP event), check if there's at least a second of difference
(like we do for other GAP-related checks in qtdemux) before
deciding to push a GAP event downstream.
qtdemux.c: In function ‘gst_qtdemux_configure_stream’:
qtdemux.c:7764:34: error: suggest parentheses around ‘&&’ within ‘||’ [-Werror=parentheses]
if ((stream->n_samples == 1) && (stream->first_duration == 0)
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid computing frame rate when a stream contain moof with only one
sample, to avoid an assert. The moof is considered as still picture.
The same is already done for one sample given in the moov.
https://bugzilla.gnome.org/show_bug.cgi?id=782217
... which no longer worked due to unconditionally clearing sample info and
ending up in inconsistent state. Let's tread a bit more carefully and also
allow for the old seek handling that resorts to scanning if no mfra info
is available.
In push mode we process as much as possible in the adapter. When we receive
a DISCONT buffer which we can't match to an actual sample (based on the existing
sample table) and there is still data remaining in the incoming adapter,there is
one of two cases happening:
1) We are doing reverse playback, in which case we should flush out all pending
data
2) We have leftover data from the previous incoming buffer... which we can't do
anything about.
For the second case, make sure we flush out the remaining data so that we can start
parsing again from scratch.
https://bugzilla.gnome.org/show_bug.cgi?id=781319
Make sure offset and neededbytes are properly resetted when all
streams are EOS in push-mode.
Avoids cases when some data might still be pushed by upstream (because
it didn't yet see the resulting GST_FLOW_EOS yet) and qtdemux gets
completely lost.
https://bugzilla.gnome.org/show_bug.cgi?id=781266
Before pushing a sample, check if there was a change in the current
stsd entry. This patch also assumes that the first stsd entry is
used as default for the first sample. It might cause an uneeded
caps renegotiation when this isn't the case.
stsd can have multiple format entries, parse them all.
This is required to play DVB DASH profile that uses multiple entries
to identify the different available bitrates/options on dash streams
The stream format-specific data is not stored into QtDemuxStreamStsdEntry
