A blocking pad probe is added on new sink pads, it's usually removed after the
caps have been negotiated or the signaling state switched to stable, but if that
never happens and the pad is released we kept the pad probe active, leaving the
pad blocked, preventing clean disposal.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4533>
The original BUNDLE support commit placed a queue after the
rtpfunnel that combines streams, but I don't see a good reason for
it. It has default settings, so if network output is slow might
accidentally store up to 1 second of pending data, increasing
latency.
Remove it in favour of doing any necessary buffering before
webrtcbin. If it turns out that there is a reason for it to
exist, the limits should probably be configurable and small.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3437>
When picking an available payload type, we need to pick one that is
available across all media.
The previous code, when multiple media were present, looked at the first one,
noticed it had pt 96 as the media pt, then simply looked at the next media,
noticed it didn't, and decided 96 was available.
Instead, check if the pt is used by any of the media, if it is, decide
it is not available and go to the next pt. I'm fairly sure that was the
original intent.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2984>
This avoids getting in a bunch of corner cases. We'd have to insert
a "rejected" line from the start as a place-holder to get around this,
but the rest of the code just becomes more complicated, so just
disallow it for now.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2439>
We need GStreamer elements to do the bandwidth estimation as this way
they can also control the pacing of the transmission flow as specified
in the [GCC] algorithm for example.
Bandwidth estimator element are placed right before the "RTPSession" as
an "rtp-aux-sender" element. This way they can use the "Transport-wide
Congestion Control" RTCP feedback messages through the "RTPTwcc" custom
events that are sent by the rtpsession.
Applications are responsible to react to the bandwidth estimator element
and set the encoder target bitrate etc... which means that we can not
pass an estimator as an element factory, so a signal as been chosen
instead.
[GCC]: https://datatracker.ietf.org/doc/html/draft-ietf-rmcat-gcc-02
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2562>
This allows the reception of streams that don't exactly match
the codec preferences. In particular, the ssrc in the codec preferences
is local sender SSRC, the other side is expected to send a different SSRC.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2615>
This new signal allows data-channel consumers to configure signal handlers on a
newly created data-channel, before any data or state change has been notified.
The webrtcin unit-tests were refactored to make use of this new signal.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2427>
WHen bundling, if multiple medias are used with the same media payload, then
each of the fec/rtx/red additions would add a distinct payload. This could
very easily overflow the available payload space.
Instead, track the relationship between the media payload value and
the relevant fec/rtx/red payload values and reuse them whenever
necessary, even when bundling.
e.g.
...
a=group:BUNDLE video0 video1
m=video 9 UDP/SAVPF 96 97
a=mid:video0
a=rtpmap:96 VP8/90000
a=rtpmap:97 rtx/90000
a=fmtp:97 apt=96
...
m=video 9 UDP/SAVPF 96 97
a=mid:video1
a=rtpmap:96 VP8/90000
a=rtpmap:97 rtx/90000
a=fmtp:97 apt=96
...
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2474>
Input (sink pads) is the already-ssrc-muxed stream with the relevant rtp
sdes header extensions already applied:
- mid
- stream-id
- repaired-stream-id
Output (src pads) have the pads separated into individual ssrc's as
that's what rtpbin gives us.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1664>
Each rtpbin exposed recv_src pad is now exposed as webrtcbin src_%u pad
now with no meaining applied to the value of %u. Previously this used
to mean the mline in the SDP. If this is is still required, then the
transceiver can be retrieved from the pad and the "mlineindex" property
from the transciever. The "mid" is also retrievable from the
transceiver.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1664>
This reverts commit 3cad3455377d5a22faa138d9df840257059776c8.
That commit was breaking the association between an audio and
a video track in the standard case.
In practice, to support carrying separate MediaStream, we are
going a way to map what MediaStreamTrack belong to what MediaStream,
but that will require some thinking about the API.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2023>
From https://datatracker.ietf.org/doc/html/draft-ietf-mmusic-msid-16:
> Multiple media descriptions with the same value for msid-id and
> msid-appdata are not permitted.
Our previous implementation of simply using the CNAME as the msid
identifier and the name of the transceiver as the msid appdata was
misguided and incorrect, and created issues when bundling multiple
video streams together: the ontrack event was emitted with the same
streams for the two bundled medias, at least in Firefox.
Instead, use the transceiver name as the identifier, and expose
a msid-appdata property on transceivers to allow for further
customization by the application. When the property is not set,
msid-appdata can be left empty as it is specified as optional.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2003>
We bind transceivers' fec_percentage property to the FEC encoder
percentage property, and with the binding bidirectional a deadlock
was introduced by the latest changes from !1762:
We take hold of the transceiver's object lock, then add the binding
and set the property to its initial value on the encoder, which causes
set_property to deadlock in the transceiver when the binding kicks in.
Changing the binding type to DEFAULT (source to target) is enough
to address the deadlock and still serves the original intent.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1967>
We need to always add the RTX/RED/ULPFEC elements as rtpbin will only
call us once to request aux/fec senders/receivers.
We also need to regenerate the media section of the SDP instead of
blindly copying from the previous offer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1762>
