Refactor the code for parsing and generating the Range, taking
advantage of existing API in GstRtspTimeRange.
Only use the TCP protocol in that mode, as per the specification.
Generate an accurate segment when in that mode, and signal to the
depayloader that it should not generate its own segment, through
the "onvif-mode" field in the caps, see
<https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/merge_requests/328>
for more information.
Translate trickmode seek flags to their ONVIF representation
Expose an onvif-rate-control property
Forwarding a single segment event from the pad that first gets
chained is incorrect: when that first event was sent by an element
such as x264enc, with its offset start, we end pushing out of segment
buffers for the other pad(s).
Instead, everytime the active pad changes, forward the appropriate
segment event.
Fixes https://gitlab.freedesktop.org/gstreamer/gst-plugins-bad/issues/1028
When it is not clear yet if a packet relative to a source should be
pushed, the packet is put into a queue, this happens in two cases:
- the source is still in probation;
- there is a large jump in seqnum, and it is not clear what
the cause is, future packets will help making a guess.
In either case stats about received packets are not updated at all; and
even if they were, when init_seq() is called it resets all receiver
stats, effectively loosing any possible stat about previously received
packets.
Fix this by taking into account the queued packets and update the stats
when calling init_seq().
Since commit c971d1a9a (rtpsource: refactor bitrate estimation,
2010-03-02) bytes_received filed in RTPSourceStats is set but then never
used again, expose it so that it can be used by user code to verify how
many bytes have been received.
According to RFC3550 lower-level headers should be considered for
bandwidth calculation.
See https://tools.ietf.org/html/rfc3550#section-6.2 paragraph 4:
Bandwidth calculations for control and data traffic include
lower-layer transport and network protocols (e.g., UDP and IP) since
that is what the resource reservation system would need to know.
Fix the source data to accommodate that.
Assume UDPv4 over IP for now, this is a simplification but it's good
enough for now.
While at it define a constant and use that instead of a magic number.
NOTE: this change basically reverts the logic of commit 529f443a6
(rtpsource: use payload size to estimate bitrate, 2010-03-02)
adjust/port from rtph264pay and allow sending the configuration data at
every IDR
The payloader was stripping the configuration data when the
config-interval was set to 0. The code was written in such a way !(a >
0) that it stripped the config when it was set at -1 (send config_data
as soon as possible).
This resulted in some MPEG4 streams where no GOP/VOP-I was detected to
be sent out without configuration.
In reverse playback, we don't want to rely on the position of the current
keyframe to decide a stream is EOS: the last GOP we push will start with
a keyframe, which position is likely to be outside of the segment.
Instead, let the normal seek_to_previous_keyframe mechanism do its job,
it works just fine.
If a key unit seek is performed with a time position that matches
the offset of a keyframe, but not its actual PTS, we need to
adjust the segment nevertheless.
For example consider the following case:
* stream starts with a keyframe at 0 nanosecond, lasting 40 milliseconds
* user does a key unit seek at 20 milliseconds
* we don't adjust the segment as the time position is "over" a keyframe
* we push a segment that starts at 20 milliseconds
* we push a buffer with PTS == 0
* an element downstream (eg rtponviftimestamp) tries to calculate the
stream time of the buffer, fails to do so and drops it
When the seek event contains a (newly-added) trickmode interval,
and TRICKMODE_KEY_UNITS was requested, only let through keyframes
separated with the required interval
The primary video stream is used to select fragment cut points
at keyframe boundaries. Auxilliary video streams may be
broken up at any packet - so fragments may not start with a keyframe
for those streams.
The time_position field of the stream is offset by the media_start
of its QtDemuxSegment compared to the start of the GstSegment of
the demuxer, take it into account when making comparisons.
If the conflict is detected when sending a packet, then also send an
upstream event to tell the source to reconfigure itself.
Also ignore the collision if we see more than one collision from the same
remote source to avoid problems on loops.
Add a new property "do-aggregate"* to the H.264 RTP payloader which
enables STAP-A aggregation as per [RFC-6184][1]. With aggregation enabled,
packets are bundled instead of sent immediately, up until the MTU size.
Bundles also end at access unit boundaries or when packets have to be
fragmented.
*: The property-name is kept generic since it might apply more widely,
e.g. STAP-B or MTAP.
[1]: https://tools.ietf.org/html/rfc6184#section-5.7
Closes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/434
