If we get anything from 7 to 126 as type when parsing
a metadata block header, we are likely dealing with a
FLAC stream version we don't fully understand. Issue
a warning if so.
Document function assumptions regarding the passed-on
type while at this.
As CRCs are calculated for the comparition already, we
might as well (cheaply) inform the user how the numbers
differ if a missmatched pair is found.
While at it:
Rephrase candidate-frame message to make more sense
There might be multiple LOAS config in a row in a full frame. The first
one might be a multi-layer config (which we can't properly parse yet)...
but then followed by a valid (single-layer) one.
The code was previously skipping whole frames (instead of just the LOAS
config we failed to read) resulting in multiple frames (seen up to 6s in
some situation) being dropped before finally getting the configuration.
https://bugzilla.gnome.org/show_bug.cgi?id=758826
On reading LOAS config, flag v=1 and vA=1 combination can occur, leading to warning
"Spec says "TBD"...". Returning TRUE on this case while parameters 'sample_rate' and
'channels' are pointing to uninitialized values can end on setting random values as
rate and channels on src caps.
https://bugzilla.gnome.org/show_bug.cgi?id=755611
It's normal when dropping into the middle of a stream to
not always have the config available immediately, so skip LOAS
until a valid config is seen without either setting invalid
caps or erroring out.
https://bugzilla.gnome.org/show_bug.cgi?id=751386
flac contains the sample offset in the frame header, so after a seek
without index flacparse will know the exact position we landed on and
timestamp buffers accordingly. It only set the pts though, which means
the baseparse-set dts which was set to the seek position prevails, and
since the seek was based on an estimate, there's likely a discrepancy
between where we wanted to land and where we did land, so from here on
that dts/pts difference will be maintained, with dts possibly multiple
seconds ahead of pts, which is just wrong. The easiest way to fix this
is to just set both pts and dts based on the sample offset, but perhaps
parsed audio should just not have dts set at all.
https://bugzilla.gnome.org/show_bug.cgi?id=752106
Adds two extra checks:
- Sampling frequency on header can't be 15.
- Frame size should be at least 9 or 7, depending
on whether CRC protection is present.
https://bugzilla.gnome.org/show_bug.cgi?id=724638
According to ISO/IEC 13818-7, "channel_config" field in ADTS header
may have value of 0, as in the case of frame with PCE.
gst_aac_parse_detect_streams() returned FALSE for those frames
and discarded them.
The parser can accept input that is not completely specified. Use the
ACCEPT_INTERSECT flag on the sinkpad to tweak the acceptcaps function to
check for intersection only. This allows us to proxy downstream
constraints while still allowing non-subset caps as input.
We can then also remove the appended template caps workaround.
Make a unit-test to check the new feature.
This reverts commit 26040ee38c
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=705024
This patch will prepend ADTS headers to raw AAC audio frames, allowing
upstream elements to link to decoders that only support AAC in ADTS format.
Note that no error correction bits are added to ADTS frames in this code.
https://bugzilla.gnome.org/show_bug.cgi?id=615740
Some muxers (eg, qtmux) only support raw AAC, so this allows linking
an encoder that outputs ADTS only to those muxers.
The conversion is simple (omit the first 7 or 9 bytes of the frame),
but has to be done in pre_push instead of handle_frame as 1.0 does
not seem to allow skipping bytes there as 0.10 used to.
Other conversions are not supported (yet).
According to http://wiki.multimedia.cx/index.php?title=ADTS,
the value stored in ADTS headers is one less than the object
type of the AAC stream.
A look at ffmpeg shows it also adds 1 to the value read off
the ADTS header.
Note that this might break other things that happen to have
an inverse off by one to match the existing code.
gst-plugins-good/gst/audioparsers/gstsbcparse.c: In function 'gst_sbc_parse_handle_frame':
gst-plugins-good/gst/audioparsers/gstsbcparse.c:210:32: error: 'ch_mode' may be used uninitialized i
Otherwise we will intersect with the srcpad template caps and add all the caps fields
that the parser will ever set, no matter if downstream restricts this field or not.
This requires upstream to set this field on the caps to successfully negotiate.
https://bugzilla.gnome.org/show_bug.cgi?id=690184
If we run into any header parsing issues and we have a valid
STREAMINFO header already, don't error out, but just stop
header parsing and try to find some audio frames.
https://bugzilla.gnome.org/show_bug.cgi?id=684701
This ensures the detection (and proper downstream caps settings) will
actually happen when we have new incoming caps without codec_data.
This was easily triggered by streams from matroskademux which initially
provided caps with a constructed codec_data, but then pushed new caps
without the codec_data once it detected the stream was adts.
