We were ignoring these before the port to 4.0, interpreting them
as GST_FLOW_ERROR / GST_ELEMENT_ERROR causes check failures.
We should start using GST_*_DECODER_ERROR in latter commits,
for now simply restore the previous behaviour.
avcodec_align_dimensions2 uses context->pix_fmt to make its
calculations, we thus need to make sure it is adequately set
when calling it.
Fixes:
gst-launch-1.0 videotestsrc ! video/x-raw, width=1920, height=1080 \
! avenc_mpeg4 ! avdec_mpeg4 ! xvimagesink
This showed invalid writes under valgrind, then segfault.
https://bugzilla.gnome.org/show_bug.cgi?id=792900
The remaining use of CODEC_ are codec flags that has been moved into the
new codec private properties or have been deperated. Will be fixed in
later patches.
https://bugzilla.gnome.org/show_bug.cgi?id=792900
This reverts commit 4284d791bc.
It causes crashes on various h264 and DNXHD/VC3 streams, where the
decoders write to arbitrary memory far after what we've allocated.
As a side effect, left/right green bars goes away when using
xvimagesink. I just think that xv cropping is broken, so this is
probably just hiding a bug.
When switching playback modes, like from TRICKMODE or TRICKMODE_KEY_UNITS
back to regular playback, we need to make sure we set the skip mode
back to the default setting.
While this field would be properly reset when we *have* feedback from
downstream (i.e. diff != G_MAXINT64), it would not be reset during
the initial phase (i.e. when the decoder hasn't pushed a buffer yet,
and therefore the sink hasn't sent back QoS information).
This avoids dropping plenty of frames when going back to regular playback
Several decoders will only be able to report a real latency (has_b_frames)
once they're actually initialized (i.e. when they return their first frame).
Doing it earlier (in set_format) doesn't guarantee that the AVCodecContext
has_b_frames has been properly initialized.
https://bugzilla.gnome.org/show_bug.cgi?id=766362
Handling slice_offset in avviddec is resulting in invalid memory read.
Since rv decoders anyways handle slice_offset, removing the same to fix
memory mishandlings
https://bugzilla.gnome.org/show_bug.cgi?id=758726
If downstream does not provide a (usable) pool, we would use our internal
pool. But the internal pool might be configured with a different width/height
because of padding, which then will cause problems if we push buffers from it
directly downstream.
Instead create a new pool if the width/height is different.
This prevents crashes with vaapisink and d3dvideosink for example.
Based on the debugging results and discussions with
Nicolas Dufresne <nicolas.dufresne@collabora.com>
https://bugzilla.gnome.org/show_bug.cgi?id=758344
... since they handle separate cases in video decoder with different requirements.
Consider e.g. x264enc ! rtph264pay ! identity drop-probability=0.1 ! rtph264depay
to illustrate a need for such separation.
Since gst_buffer_pool_set_config() takes ownership of the config structure,
it is only necessary to free the structure before using it when the true
branch of if (gst_buffer_pool_config_validate_params) hasn't run.
gst_buffer_pool_set_config() always takes ownership of the structure
regardless of success or failure. Which means the return, checked with
if (!working_pool), has no relation to the state of the structure.
Change default alignment from 16 to 32 bytes, which fixes crashes
when decoding H.265 using AVX2-based decoder code paths and when
using ximagesink/glimagesink.
https://bugzilla.gnome.org/show_bug.cgi?id=754120
Make sure the alignment requirement in GstAllocationParams
matches the GstVideoAlignment requirements. This fixes
issues with avdec_h265 crashing in the avx2 code path when
used with playbin and ximagesink/glimagesink as videosink.
The internal video pool would allocate buffers with an
alignment of 15 even though GstVideoAlignment specified
a stride_align requirement of 31 (which comes from ffmpeg).
https://bugzilla.gnome.org/show_bug.cgi?id=754120
Some check where incorect and also unsafe. The only reliable information
in get_buffer2 is the picture width/height really. The side effect is
that the width/height of the internal pool endup padded, so when we
switch we also need to switch to the a new width/height, hence we save
the pool info.
https://bugzilla.gnome.org/show_bug.cgi?id=753869
