Commit 7873bede31
(https://bugzilla.gnome.org/show_bug.cgi?id=760774) changed the
behaviour of qtdemux to call gst_qtdemux_configure_stream() for
every new moof.
When playing a protected stream, gst_qtdemux_configure_stream()
calls gst_qtdemux_configure_protected_caps(). The
gst_qtdemux_configure_protected_caps() function takes the original
media format, puts this in a field called "original-media-type"
and then changes the caps to "application/x-cenc".
The gst_qtdemux_configure_protected_caps() did not handle the case
of being called multiple times, causing it to incorrectly set the
caps. The second call was causing the caps to be set to:
application/x-cenc, original-media-type"application/x-cenc"
This commit makes gst_qtdemux_configure_protected_caps() check that
the caps have already been transformed, so that it only gets
changed once.
https://bugzilla.gnome.org/show_bug.cgi?id=761769
qtdemux calculates framerate using duration and the number of sample.
In case of fragmented mp4 format, however, the number of sample can
be figure out after parsing every moof box. Because qtdemux does not
parse every moof in QTDEMUX_STATE_HEADER state, it will cause incorrect
framerate calculation.
This patch will triger gst_qtdemux_configure_stream() for every new moof.
Then, framerate will be calculated by using duration and n_samples of the moof.
https://bugzilla.gnome.org/show_bug.cgi?id=760774
Based on document ISO_IEC_14496-12, edit list box can have
segment duration as zero. It does not imply that media_start equals to
media_stop. But, it just indicates a sample which should be presented
at the first. This patch derives segment duration using media_time
and duration of file. And set derived duration to segment-duration.
https://bugzilla.gnome.org/show_bug.cgi?id=760781
In case of push mode, qtdemux expose streams after got moov box.
We can not guarantee that a moov box has sample data such as sample duration
and the number of sample in stbl box for fragmented format case.
So, if a moov has no sample data, streams will not be exposed until get the first moof.
https://bugzilla.gnome.org/show_bug.cgi?id=760779
Prevents downstream from receiving flushes for a seek only in
upstream. Those seeks are only to start reading from the right
offset when skipping or returning to qt atoms.
https://bugzilla.gnome.org/show_bug.cgi?id=758928
Avoid writing a negative number as a large positive
integer in an edit list when the first_ts is smaller
than the first_dts - which can happen when the first
packet received has a PTS but no DTS.
https://bugzilla.gnome.org/show_bug.cgi?id=759615
When working in push-mode, we attempt to push out everything currently
buffered in the adapter.
This has two pitfalls:
* We could stop earlier (the moment we get a non-ok or non-not-linked)
* We return the last combined flow return, which might be completely
different from the previous combined flow return
When seeking back to restore the mdat position a flush is pushed
through and it resets downstream segment information. Make sure
that after the flush (that does a soft reset) a segment will
be pushed again
Fixes regressions spotted at
https://ci.gstreamer.net/job/GStreamer-master-validate/2100/
10 FourCCs generated with GST_MAKE_FOURCC() in gstqtmux.c and atoms.c
already exist in fourcc.h. Don't duplicate these and use them directly.
Plus moving 6 to fourcc.h, to centralize them all.
This fixes seeking if the first entries in the samples table are negative. The
binary search would always fail on this as the array would not be sorted if
interpreting the negative numbers as huge positive numbers. This caused us to
always output buffers from the beginning after a seek instead of close to the
seek position.
Also add a case to the comparison function for equality.
It would be unusual to have the header segment with an 'edts' atom
indicating gaps at the beginning when handling fragmented streams.
The header usually doesn't contain any timestamping information, this
should come from the playlist/manifest and the segments with media
in those scenarios.
https://bugzilla.gnome.org/show_bug.cgi?id=758171
In push-mode it is hard to support qt segments overall but it is
possible to support when the file isn't heavily edited but just contain
a segment to indicate a gap at the beginning. This also allows properly
timestamping data that has negative DTS in push-mode.
It is relevant to support those for 2 scenarios:
1) fragmented streaming
2) HTTP playback of 'regular' mp4
https://bugzilla.gnome.org/show_bug.cgi?id=753484
If the QtDemuxStream are re-used they may already have caps which used
to be leaked.
Reproduced using the
validate.dash.playback.seek_forward.dash_exMPD_BIP_TC1 validate
scenario.
https://bugzilla.gnome.org/show_bug.cgi?id=756561
Negotiation to audio/x-raw,format=S8 was not possible because S8 does
not have a bit order so we ended up doing `if (!entry.fourcc) goto refuse_caps;`
https://bugzilla.gnome.org/show_bug.cgi?id=756387
If seeking targets an empty segment skip it as there is no media
offset to get from it. Instead look for the next one.
This doesn't make seeking in push-mode work if you seek to an
empty segment but at least won't get you to wrong offsets.
https://bugzilla.gnome.org/show_bug.cgi?id=753484
eceb2ccc73 broke segment seeks by always
accumulating segments manually when activating a segment. This is only
needed when handling edit lists, not when activating a segment because of a
seek. Do the accumulation when switching edit list segments instead.
This fixes segment seeks again, while keeping edit lists playback working.
https://bugzilla.gnome.org/show_bug.cgi?id=755471
Commit 7d7e54ce68 added support for
DASH common encryption, however commit
bb336840c0 that went onto master
shortly before the CENC commit caused the calculation of the CENC
aux info offset to be incorrect.
The base_offset was being added if present, but if the base_offset
is relative to the start of the moof, the offset was being added twice.
The correct approach is to calculate the offset from the start of the
moof and use that offset when parsing the CENC aux info.
