Variable f1 is never used, so just skip that loop for now.
The test has never actually tested actual resampling because of
that bug it seems, and the test fails if fixed to actually resample.
For now we just avoid the pointless 126*12 pipelines that were just
testing the same thing (nothing) over and over again.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7827>
The typefind code was rejecting content smaller than 128 bytes making it
impossible to play files with very small srt files.
But those can actually be properly detected so fix typefind to allow
smaller content and try its best with it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6937>
It was adding and subtracting the segment base here and there, but it
was also doing so incorrectly, leading to various calculation errors.
Fixed a few bugs uncovered, related to getting a new segment:
* If we reset base_ts/next_ts/out_frame_count, also reset prevbuf
* Only do so if the new segment is different than the previous one
Also replaced a few occurrences of GST_BUFFER_TIMESTAMP with
GST_BUFFER_PTS for consistency.
Integrated the tests of
https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2186
, now passing. The test_segment_update_same test had to be fixed,
because it was wrongly assuming that we would not fill the gap inside
the new-but-same segment.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6031>
This allows metas to be serialized to be transmitted or stored. This is
intended to be used for example by gdppay or unixfdsink.
Implemented on GstCustomMeta, GstVideoMeta, GstReferenceTimestampMeta,
and GstAudioMeta.
Sponsored-by: Netflix Inc.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5355>
Otherwise if there is a huge gap it will only be considered a
discontinuity after another discont-time amount of buffers has passed.
Like this it will be immediately a discontinuity if the gap between the
expected and received time becomes bigger than the discont-time.
The last part of the test was actually testing for this behaviour and
expected the previous behaviour. Most other tests also had to be
adjusted because discont will now happen at slightly different times
than before.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5759>
Windows does not support fork() so all tests will run in a single
process, and global variables will be reused across multiple tests.
Thus, each test should reset global variables.
Also, setup pad chain/event functions before playing state
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5752>
Adds list of formats that should be used by element in needs to passthrough
video. It contains the full list of video format plus DMA_DRM format
and will be extended in the future as needed. This patches includes 3 new
symbols:
- GST_VIDEO_FORMATS_ANY_STR
- GST_VIDEO_FORMATS_ANY
- gst_video_formats_any()
The last one can be used by bindings or for code that prefers having
GstVideoFormat values instead of strings.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5386>
Fixes a potential GPU stall if an immediately freed texture/buffer is
attempted to be reused immediately by the CPU, e.g. when uploading.
Problematic scenario is this:
1. element does GPU processing reading from texture
2. frees the buffer back to the pool
3. pool acquire returns the just released buffer
4. GPU processing then has to wait for the previous GPU operation to
complete causing a stall
If there was a reliable way to know whether a buffer had been finished
with across all GPU drivers, we would use it. However as that does not
exist, this workaround is to keep the released buffer unusable until the
next released buffer.
This is the same approach as is used in the qml (Qt5) elements.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5144>
If a depayloader aggregates multiple RTP buffers into one buffer only
the last RTP buffer was checked for header extensions. Now the
depayloader remembers all RTP packets pushed before a output buffer is
pushed and checks all RTP buffers for header extensions.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4979>
These 10bit formats are identical to NV12_16L32S, but 64bytes of data is being
prefixed with 16bytes data with four pixels of lower 2bits per byte. For
MT2110T, the lower two bits set so each bytes contains a column of 4 pixels,
also describe as tiled lower 2 bits. MT2110T has been chosen as a name to match
the vendor chosen name. This format is unlikely to exist for other vendors.
For MT2110R, the 2 low bits are in raster order.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3444>
The current limit is `x10`, which allows just `+20 dB` of gain.
While it may seem sufficient, this came up as a problem
in a real-world, non-specially-engineered situation,
in strawberry's EBU R 128 loudness normalization.
(https://github.com/strawberrymusicplayer/strawberry/pull/1216)
There is an audio track (that was not intentionally engineered that way),
that has integrated loudness of `-38 LUFS`,
and if we want to normalize it's loudness to e.g. `-16 LUFS`,
which is a very reasonable thing to do,
we need to apply gain of `+22 dB`,
which is larger than `+20 dB`, and we fail...
I think it should allow at least `+96 dB` of gain,
and therefore should be at `10^(96/20) ~= 63096`.
But, i don't see why we need to put any specific restriction
on that parameter in the first place, other than the fact
that the fixed-point multiplication scheme does not support volume
larger than 15x-ish.
So let's just implement a floating-point fall-back path
that does not involve fixed-point multiplication
and lift the restriction altogether?
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5063>
Don't assume that compositor will output only single buffer
for single input buffer. If buffer's running time is not completly
aligned to output buffer running time or duration, compositor
can generate multiple buffers. If that happens, two threads,
one is aggregator output thread and main thread were trying
to modify buffer in this test. Clear the buffer after
shutting down pipeline to avoid the race.
Fixes: https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/2836
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5081>
The current implementation copies metas without checking if the buffer
is writable.
The operation that needs to be done, replacing the input buffer and
copying the metas, is only part of that process. We create a new function
that does both.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4912>
Fixes test: validate.uridecodebin.expose_raw_pad_caps
testsrcbin (currently part of debugutilsbad) is an useful element for
validate tests.
validate.uridecodebin.expose_raw_pad_caps makes use of it.
Unfortunately, because validate tests with GStreamer only run with
whitelisted plugins and `debugutilsbad` wasn't in the whitelist, the
test was failing and being auto-skipped.
This patch adds debugutilsbad to the whitelists used by validate tests
in subprojects with a validate/meson.build.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4931>
