There are some few but certain conditions where it is possible for the
dest_width to be smaller than x. So we check this before assigning a negative
value to src_width, which is a unsigned and would be promoted to a number that
can segfault videoblend.
https://bugzilla.gnome.org/show_bug.cgi?id=738242
This was never reset when going from PAUSED->READY and resulted
in encoders being not reusable after EOS. They just rejected any
buffer because they received EOS in their previous life.
The flag wasn't used anywhere except for rejecting buffers after
EOS, and this is now handled by GstPad directly.
Move the conversion code used in videoconvert to the video library
and expose a simple but generic API to do arbitrary conversion. It can
currently do colorspace conversion but the plan is to add videoscale to
it as well.
See https://bugzilla.gnome.org/show_bug.cgi?id=732415
Reset last_timestamp_out when applying the output segment
change, to avoid decoder confusion over new timestamp timelines when
a seamless segment change happens.
Move some locks/unlocks to later when they're actually needed.
https://bugzilla.gnome.org/show_bug.cgi?id=734617
This fixes the reverse playback scenario when upstream is not fully
parsing the stream and does not send every keyframe chain separately
with the DISCONT flag on the keyframe.
To explain this, let's suppose we have this stream:
0 1 2 3 4 5 6 7 8
K K K
In most circumstances, the upstream parser will chain in the
decoder the buffers in the following order:
6 7 8 3 4 5 0 1 2
D D D
In this case, GstVideoDecoder will flush the parse queue every time
it receives discont (D) and we will eventually get in the output queue:
(flush here) 8 7 6 (flush here) 5 4 3 (flush here) 2 1 0
In case the upstream parser doesn't do this work, though,
GstVideoDecoder will receive the whole stream at once and will flush
the parse queue afterwards:
0 1 2 3 4 5 6 7 8
D
During the flush, it will look backwards for keyframes and will
decode in this order:
6 7 8 3 4 5 0 1 2
This is the same order that it would receive from upstream if
upstream was parsing and looking for the keyframes, only that now
there is no flushing of the output queue in between keyframes,
which will result in the output queue looking like this:
2 1 0 6 5 3 8 7 6
This will confuse downstream obviously and will play incorrectly.
This patch forces the decoder to flush the output queue every time
it picks a new keyframe to decode, so it will end up decoding 6 7 8
and then flushing before picking 3 for decoding, so the output will
get 8 7 6 before 6 5 3 and the video will play back correctly.
https://bugzilla.gnome.org/show_bug.cgi?id=734441
This prevent implementing allocation query, as the format need to be
known in order to determin the size and number of buffers needed.
Note: This may lead to few regressions that will need fixing
https://bugzilla.gnome.org/show_bug.cgi?id=732288
Fix gst_video_decoder_parse_available() to really parse any pending
source data that is still available in the adapter. This is a memory
optimization to avoid expansion of video packed added to the adapter,
but also a fix to EOS condition when the subclass parse() function
ultimately only needed to call into gvd_have_frame() and no additional
source bytes were consumed, i.e. gvd_add_to_frame() is not called.
This situation can occur when decoding H.264 streams in byte-stream/nal
mode for instance. A decoder always requires the next NAL unit to be
parsed so that to determine picture boundaries. When a new picture is
found, no byte is consumed (i.e. gvd_add_to_frame() is not called)
but gvd_have_frame() is called (i.e. priv->current_frame is gone).
Also make sure to avoid infinite loops caused by incorrect subclass
parse() implementations. This can occur when no byte gets consumed
and no appropriate indication (GST_VIDEO_DECODER_FLOW_NEED_DATA) is
returned.
https://bugzilla.gnome.org/show_bug.cgi?id=731974
Signed-off-by: Gwenole Beauchesne <gwenole.beauchesne@intel.com>
Buffer pool set_config() may return FALSE if requested configuration needed small
changes. Reget the config and try setting it again. This ensure we have a configured
pool if possible.
This should allow for more meaningful errors. Dereferencing NULL
is more useful information than dereferencing a random address
happened to be on the stack.
If gst_video_overlay_rectangle_apply_global_alpha is called with
a rectangle with unsuitable alpha, expanding the alpha plane will
fail, and thus lead to dereferencing a NULL src pointer. It's not
certain this will happen in practice, as the function is static
and callers might ensure suitable alpha before calling, but there
is no apparent explicit such check.
Add prologue asserts for proper alpha to explicitely prevent this.
Coverity 1139707
Videodecoder does late renegotiation, it will wait for the next
buffer before renegotiating its caps and bufferpool. It might happen
that downstream element switched from passthrough to non-passthrough
and sent a reconfigure upstream (that caused this renegotiation).
This downstream element will ask the video sink below for the bufferpool
with an allocation query and will get the same bufferpool that
videodecoder is holding, too.
When renegotiating, if videodecoder deactivates its bufferpool it
might be deactivating the bufferpool that some element downstream
is using and cause the pipeline to fail.
https://bugzilla.gnome.org/show_bug.cgi?id=727498
baseparse will reverse each GOP for us already, so the segment events can
be after our keyframe. Make sure to get it and all other relevant sticky
events before starting to decode.
