Make sure that group-id of a given play item are made consistent from the
start (sources) and all the way through the output.
This ensures that we can reliably detect that we have switched to the next play
item on the output of decodebin3 (and we can therefore properly free/release it)
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3457>
When shutting down, we want to remove the urisourcebin blocking probes ... but
we also want to propagate a GST_FLOW_FLUSHING upstream (and not
GST_FLOW_NOT_LINKED) to make the upstream task gracefully stop instead of
posting an error message.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3457>
When `is_selection_done` is called, it checks that all the requested streams are
present in the active stream list ...
... except there could very well be a (about to be removed) stream from the
previous selection present.
Therefore filter the list of streams we add to the message by the streams which
are actually requested.
Fixes issues when switching between different stream types (ex: video-only to
audio-only).
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3457>
Previously we tried to route an incoming RTCP FB FIR to the correct ssrc
using the "media source" component of the RTCP FB message. However,
according to RFC5104 (section 4.3.1.2) the "media source" SHALL be set
to 0. Instead the ssrc(s) in use are propagated via the FCI data. Now
a specific GstForceKeyUnit event is sent for every ssrc.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3292>
RTP source statistics are tracked for local senders by
treating them as a receiver of their own outbound packets.
Accordingly, track the highest packet seqnum so that the
packets-lost calculation generates a sensible number instead
of always reporting -$number_of_packets_sent
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3454>
There was a drm/drm_mode.h included added recently, drm/ is usually
referencing the linux kernel header, but we only requires the libdrm
headers to be installed. On top of this, including drm_mode.h is never
needed as its already included by drm.h.
Fixes#1596
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3452>
When getting a "404 Not Found" response from the DESCRIBE request, the
source produced a "No supported authentication protocol was found" error
instead of passing on the 404, which was confusing.
Only produce this error message when we're handling a response of "401
Unauthorized" without a compatible WWW-Authenticate header.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3414>
The legacy emulation in DRM/KMS drivers badly interact with GStreamer and
may cause the framerate to be halved. With this property, users can disable
vsync (which is handled internally by the emulation) in order to regain the
full framerate.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3303>
The event type for instant-rate-change events was poorly chosen,
leading to them being re-sent too late and even after EOS.
Add a mechanism in GstPad for the sticky event order to be
different to the value of the event type to fix that up.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3387>
The original BUNDLE support commit placed a queue after the
rtpfunnel that combines streams, but I don't see a good reason for
it. It has default settings, so if network output is slow might
accidentally store up to 1 second of pending data, increasing
latency.
Remove it in favour of doing any necessary buffering before
webrtcbin. If it turns out that there is a reason for it to
exist, the limits should probably be configurable and small.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3437>
Currently, when rtspsrc property add-reference-timestamp-metadata=true,
a downstream rtph264depay element will attach multiple copies of the
same GstReferenceTimestampMeta to the depayloaded media buffers. This
can have signficant performance impacts further downstream in a pipeline
like the following:
rtspsrc add-reference-timestamp-metadata=true ! rtph264depay ! h264parse ! ... ! rtph264pay ! ...
For example, if there are 10 packet buffers for a frame of RTP H.264
video, each of those packet buffers will contain the same reference
timestamp meta. The rtph264depay element will then attach all 10
metadata to the depayloaded frame. And then later when we payload the
frame buffer again for proxying, we now have 10 more buffers each with
10 instance of the same metadata. Allocating/deallocating 100+ instances
of metadata @ 30fps for multiple streams has a pretty large performance
impact.
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/1578
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3431>
The tile width in pixel is not always available. Notably for
8L128 10bit format, the tile is 8x128 bytes, and the pixel
format is fully packed. That means that the tile contains at
least 6 pixels per line, but it also hold some bits of the
pixel from the same line on the previous or next tile.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3424>
In current tile representation, only tiles with power of two
width and height in bytes are supported. This limitation
prevents adding more complex tiles formats.
In this patch, we deprecate tile_ws and tile_hs from GstVideoFormatInfo and
replace if with an array of GstVideoTileInfo. Each plane tiles are then
described with their pixels width/height, line stride and total size.
The helper gst_video_format_info_get_tile_sizes() that depends on the
deprecated API is also being removed. This can simply be removed as it wasn't
in any stable release yet.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3424>
Setting force_live lets aggregator behave as if it had at least one of
its sinks connected to a live source, which should let us get rid of the
fake live test source hack that is probably present in dozens of
applications by now.
+ Expose API for subclasses to set and get force_live
+ Expose force-live properties in GstVideoAggregator and GstAudioAggregator
+ Adds a simple test
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3008>
