Signal sparse streams properly in stream-start event and force sending
of pending sticky events which have been stored on the pad already and
which otherwise would only be sent on the first buffer or serialized
event (which means very late in case of subtitle streams). Playsink in
playbin waits for stream-start or another serialized event, and if we
don't do this it will wait for the multiqueue to run full before
starting playback, which might take a couple of seconds.
https://bugzilla.gnome.org/show_bug.cgi?id=734040
All pads of a stream are now added at the beginning. In order to cope with
streams that don't get any data (forever or for a long time) we detect gaps
and push out GAP events when needed.
Cleanups and commenting by Jan Schmidt <jan@centricular.com>
https://bugzilla.gnome.org/show_bug.cgi?id=734040
If a discontinuity in the stream is detected, data is discarded until
a new PES starts. If the first packet after the discontinuity is also
the start of a PES, there is no reason to discard the packets.
https://bugzilla.gnome.org/show_bug.cgi?id=737569
It was previously a mix and match of both variants, introducing just too much
confusion.
The prefix are from now on:
* GstMpegts for structures and type names (and not GstMpegTs)
* gst_mpegts_ for functions (and not gst_mpeg_ts_)
* GST_MPEGTS_ for enums/flags (and not GST_MPEG_TS_)
* GST_TYPE_MPEGTS_ for types (and not GST_TYPE_MPEG_TS_)
The rationale for chosing that is:
* the namespace is shorter/direct (it's mpegts, not mpeg_ts nor mpeg-ts)
* the namespace is one word under Gst
* it's shorter (yah)
Co-Authored by: Thibault Saunier <tsaunier@gnome.org>
From a high level perspective, the new process for seeking h264
streams is as follows:
1) Rewind the stream until we find the first I-slice of a frame,
and mark its offset in the stream.
2) Rewind the stream until we find SPS and PPS informations,
to make sure the subsequent parser is up to date.
3) Accumulate optionnal SEI NAL units on the way.
4) Push the SPS, PPS and SEI units before the new keyframe.
https://bugzilla.gnome.org/show_bug.cgi?id=675132
Since all the other timestamp tracking now gets reset on a discont,
it makes sense to wait for a PCR and timestamp buffers like when
playback first starts
Due to mpegts streaming nature some pads are created but are only added
later to the element. This can cause a scenario where the first stream
doesn't have an available decoder (while the next ones still pending
would have) and tsdemux will fail with not-linked as the first stream
added wouldn't be linked.
To avoid this tsdemux needs to add pads to the flowcombiner
when they are created instead of only when adding them to the
element.
gst_ts_demux_push_pending_data() will check if it now can activate the
stream and add the pad, we don't have to check that ourselves.
Fixes playback of very short MPEG TS files.
Apart from just adding detection of the proper stream type, we also need to only
output the first substream (0x71) which contains the core substream.
While this does not provide *full* DTS-HD support (since it will miss the complementary
substreams), it will still work in the way legacy (non-DTS-HD) bluray players would work.
https://bugzilla.gnome.org/show_bug.cgi?id=725563
Keep a list of current global tags around and push them
whenever a new stream is started. Also convert all stream
specific tags to global as they are stream specific for
the container, so they are global for the streams from
within that container.
https://bugzilla.gnome.org/show_bug.cgi?id=644395
It is quite possible that we might get PTS/DTS before the first
PCR/Offset observation.
In order to end up with valid timestamp we wait until at least one
stream was able to get a proper running-time for any PTS/DTS.
Until then, we queue up the pending buffers to push out.
Once we see a first valid timestamp, we re-evaluate the amount of
running-time elapsed (based on returned inital running-time and amount
of data/DTS queued up) for any given stream.
Taking the biggest amount of elapsed time, we set that on the packetizer
as the initial offset and recalculate all pending buffers running-time
PTS/DTS.
Note: The buffer queueing system can also be used later on for the
dvb fast start proposal (where we queue up all stream packets before
seeing PAT/PMT and then push them once we know if they belong to the
chosen program).
ATSC ac3 streams are always guaranteed to be AC3 if EAC3 descriptor
is not present
If stream registration id is 'AC-3' then it's also guaranteed to be AC3.
Finally if AC3 descriptor is present it's guaranteed to be AC3.
Only silences a warning, but still.
The new seek handling re-creates the segment time information once it
has enough information after a seek.
The problem was that we'd completely ignore the requested rate. So store
that and use it in the newly created segment.
https://bugzilla.gnome.org/show_bug.cgi?id=694369
The program_number attribute was overloaded, trying to indicate both
the currently playing program, and the program requested via the
"program-number" property. The end result was that setting the
property didn't work (see #690934).
I added a new requested_program_number field rather than reviving the
current_program_number field because it seemed this would result in
fewer changes overall and be less confusing. It breaks symmetry with
the "program-number" property, but it retains parallels with the likes
of program->program_number.
Because gst_ts_demux_reset is called after the properties have been
parsed, requested_program_number is initialised in gst_ts_demux_init.
Whether this is exactly the right place, I don't know.
Setting the program-number property does not affect which program
is actually being demuxed.
Moving the initialization of the program_number from
gst_ts_demux_reset to gst_ts_demux_init seems to fix this issue.
https://bugzilla.gnome.org/show_bug.cgi?id=690934
* Avoids handling twice the same seek (can happen with playbin and files
with subtitles)
* Set the sequence number of the segment event to the sequence number of
the seek event that generated it (-1 for the initial one).
