This allows:
* Better duration estimation
* More accurate PCR location
* Overall more accurate running-time location and calculation
Location and values of PCR are recorded in groups (PCROffsetGroup)
with notable PCR/Offset observations in them (when bitrate changed
for example). PCR and offset are stored as 32bit values to
reduce memory usage (they are differences against that group's
first_{pcr|offset}.
Those groups each contain a global PCR offset (pcr_offset) which
indicates how far in the stream that group is.
Whenever new PCR values are observed, we store them in a sliding
window estimator (PCROffsetGroupCurrent).
When a reset/wrapover/gap is detected, we close the current group with
current values and start a new one (the pcr_offset of that new group
is also calculated).
When a notable change in bitrate is observed (+/- 10%), we record
new values in the current group. This is a compromise between
storing all PCR/offset observations and none, while at the same time
providing better information for running-time<=>offset calculation
in VBR streams.
Whenever a new non-contiguous group is start (due to seeking for example)
we re-evaluate the pcr_offset of each groups. This allows detecting as
quickly as possible PCR wrapover/reset.
When wanting to find the offset of a certain running-time, one can
iterate the groups by looking at the pcr_offset (which in essence *is*
the running-time of that group in the overall stream).
Once a group (or neighbouring groups if the running-time is between two
groups) is found, once can use the recorded values to find the most
accurate offset.
Right now this code is only used in pull-mode , but could also
be activated later on for any seekable stream, like live timeshift
with queue2.
Future improvements:
* some heuristics to "compress" the stored values in groups so as to keep
the memory usage down while still keeping a decent amount of notable
points.
* After a seek compare expected and obtained PCR/Offset and if the
difference is too big, re-calculate position with newly observed
values and seek to that more accurate position.
Note that this code will *not* provide keyframe-accurate seeking, but
will allow a much more accurate PCR/running-time/offset location on
any random stream.
For past (observed) values it will be as accurate as can be.
For future values it will be better than the current situation.
Finally the more you seek, the more accurate your positioning will be.
The previous code could enter an infinite loop because the adapter state
could get out of sync with its mapped data state after sync was lost.
The code was pretty confusing so it's been rewritten to be clearer.
The easiest way to reproduce the infinite loop is to use the breakmydata
element before tsdemux to trigger a resync.
https://bugzilla.gnome.org/show_bug.cgi?id=708161
If ever we lose sync, we were just checking for the next 0x47 marker ...
which might actually happen within a mpeg-ts packet.
Instead check for 3 repeating 0x47 at the expected packet size interval,
which the same logic we use when we initially look for the packet size.
We were only resetting the first 512 values of the lookup table instead
of the whole 8192.
This resulted in any PCR PID over 0x0200 ... ending up taking the first PCR
table around :(
Helps with debugging issues. And also remove unused variable (opcr)
This will also allow us in the future to properly detect:
* random-access location (to enable keyframe observation and
potentially seeking
* discont location (to properly handle resets)
* splice location (to properly handle new stream changes)
This is actually a workaround (we'll be skipping the upcoming section)
This will only happen for sections where the beginning is located within
the last 8 bytes of a packet (which is the minimum we need to properly
identify any section beginning).
Later we should figure out a way to store those bytes and mark that
some analysis needs to happen. The probability of this happening is
too low for me to care right now and do that fix. There is a good chance
that section will eventually be repeated and won't end up on such border.
* packet.origts is no longer used since the PCR refactoring done ages ago
* known_packet_size is a duplicate of packet_size != 0
* caps was never used outside of the packetizer
We had two issues with the previous code:
1) We were badly handling PUSI-flagged packets. We were discarding the
initial data (if pointer != 0) whereas we should have been accumulating
it with the previous data (if there was a continuity of course).
=> First series of information loss
2) We were not checking whether there were more sections after the end
of one (i.e. when the following byte was not a stuff byte).
This fixes those two issues.
Fixes#677443https://bugzilla.gnome.org/show_bug.cgi?id=677443
* Only mpeg-ts section packetization remains.
* Improve code to detect duplicated sections as early as possible
* Add FIXME for various issues that need fixing (but are not regressions)
https://bugzilla.gnome.org/show_bug.cgi?id=702724
Only create subtables when needed. It was previously creating one every
single time ... to check if one was present.
And speed up code to detect whether a subtable was already present or not.
Overall makes section pushing 2 times faster.
In some cases (NIT on highly-populated DVB-C operator for example), there
will be more than one section emitted for the same subtable and version
number.
In order not to lose those updates for the same version number, we checked
against the CRC of the previous section we parsed.
The problem is that, while it made sure we didn't lose any information, it
also meant that if the same section came back (same version, same CRC) later
on we would re-process it, re-parse it and re-emit it.
This version improves on that by keeping a list of previously observed CRC
for identical PID/subtable/version-number and will only process sections if
they really were never seen in the past (as opposed to just before).
On a 30s clip, this brings down the number of NIT section parsing from 4541
down to 663.
https://bugzilla.gnome.org/show_bug.cgi?id=614479
Sync byte scan is incorrect for M2TS streams because the timestamp 4
bytes were not included in the flush size. This can result in an
infinite loop.
Rework the scan code to be clearer and work in all cases.
descriptors are stored as a GValueArray of GString. The downside is
that there is no way to "pass" ownership of a GValue to a GValueArray
which previously resulted in expensive copy/free of the (already expensive)
GString.
Here we estimate first the size of the GValueArray, then create it,
then directly use the GValue of that array.
Speeds up total SI parsing by ~30%
When dealing with non-time based push-mode streams, we need to revert
to using the offset-based PCR/PTS estimation logic of packetizer.
This solves uses cases such as:
pushfile:// ! tsdemux
src ! queue ! tsdemux
https://bugzilla.gnome.org/show_bug.cgi?id=687178
Original code to parse satellite delivery descriptors to generate
"satellite" structures appeared to be copy & pasted from cable's code
without amending for satellite.
Also added 8PSK to dvbsrc's enum for modulation.
https://bugzilla.gnome.org/show_bug.cgi?id=654485
Conflicts:
gst/mpegdemux/gstmpegdesc.h
gst/mpegdemux/mpegtspacketizer.c
