gstkmssink.c: In function ‘gst_kms_sink_get_input_buffer’:
gstkmssink.c:1102:29: error: ‘mems[0]’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
kmsmem = (GstKMSMemory *) get_cached_kmsmem (mems[0]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Configure the display mode when setting the negotiated caps instead of
during showing the first frame.
A framebuffer is required to set the mode. Allocate a buffer object
according to the negotiated caps and use it to set the mode. This buffer
object cannot be freed until another page flip happened on the crtc
(i.e., until the first frame is rendered).
https://bugzilla.gnome.org/show_bug.cgi?id=773473
Signed-off-by: Víctor Manuel Jáquez Leal <vjaquez@igalia.com>
The force-modesetting parameter forces the kmssink to ignore already
configured display modes, to configure the display mode itself and use
the base plane for output.
https://bugzilla.gnome.org/show_bug.cgi?id=773473
If the input buffers have a different size than the display, the frames
would have to be scaled or positioned on the display. The kmssink cannot
decide which behaviour would be appropriate for which use case.
In order to avoid scaling or positioning of the input stream, allow only
the supported connector resolutions in the sink caps.
https://bugzilla.gnome.org/show_bug.cgi?id=773473
Signed-off-by: Víctor Manuel Jáquez Leal <vjaquez@igalia.com>
Displays usually support multiple modes. Therefore, the kmssink should
not only support the preferred mode, but any mode that is supported by
the display.
https://bugzilla.gnome.org/show_bug.cgi?id=773473
The kmssink assumed that the mode was already set by another application
and used an overlay plane for displaying the frames.
Use the preferred mode of the monitor and render to the base plane if
the crtc does not have a valid mode.
https://bugzilla.gnome.org/show_bug.cgi?id=773473
Signed-off-by: Víctor Manuel Jáquez Leal <vjaquez@igalia.com>
libkms should not be used, because it imposes limitations on the DRM
API, especially regarding bpp and stride. Instead the DRM IOCTL should
be used directly.
Switch from libkms to the IOCTL interface. Set bpp and height for
framebuffer allocation to properly handle planar video formats.
https://bugzilla.gnome.org/show_bug.cgi?id=773473
Signed-off-by: Víctor Jáquez <vjaquez@igalia.com>
The default get_times() function of the base sink is just fine.
Remove the custom get_times() function, because the default function
already reads the timestamps from the buffers.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
https://bugzilla.gnome.org/show_bug.cgi?id=773473
In most display sink, the logic is to use as much as possible
of the given window. In this case, the window is the screen,
hence it's logical to scale up.
https://bugzilla.gnome.org/show_bug.cgi?id=767422
The source region was scaled for display before being passed
to drmModeSetPlane, which resulted in a portion of the video
being cropped. While when crop meta was present, the rectangle
was not centered since we where using unscaled width/height.
https://bugzilla.gnome.org/show_bug.cgi?id=767422
Some kms drivers demands specific pitches over the ones calculated by
GstVideoInfo. For example, intel driver demands strides round up 64.
This patch queries the driver for the prefered pitch and overwrites it
in the pool's GstVideoInfo structure.
https://bugzilla.gnome.org/show_bug.cgi?id=768446
The calculation of the offset table was done base on a plane size
estimation. This does not always work. Instead, use memory offset the
same we as it's implement in GstVideoMeta map functions.
Without setting the DRM_CLIENT_CAP_UNIVERSAL_PLANES capability bit, only
overlay planes are made available for compatibility with legacy clients.
But if a CRTC doesn't have an overlay plane associated, then kmssink is
not able to find a plane for the CRTC and the pipeline will fail, i.e:
ERROR kmssink gstkmssink.c:482:gst_kms_sink_start:<kmssink0> Could not find a plane for crtc
If no overlay planes were found for a given CRTC, fallback to universal
planes so DRM will also return primary planes that can be used instead.
https://bugzilla.gnome.org/show_bug.cgi?id=768183
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Without setting the DRM_CLIENT_CAP_UNIVERSAL_PLANES capability bit, only
overlay planes are made available for compatibility with legacy clients.
But if a CRTC doesn't have an overlay plane associated, then kmssink is
not able to find a plane for the CRTC and the pipeline will fail, i.e:
ERROR kmssink gstkmssink.c:482:gst_kms_sink_start:<kmssink0> Could not find a plane for crtc
This patch adds a plane-id property to the kmssink element so a specific
plane can be used in case that a CRTC has only a primary plane associated.
https://bugzilla.gnome.org/show_bug.cgi?id=768183
This patch requests for drmModePageFlip() for the used CRTC, if the kernel
module suppports async page flip. If it does not, the element requests for a
vblank event. A GstPoll waits for the event to happen.
https://bugzilla.gnome.org/show_bug.cgi?id=761059
This patch will enable the import of dmabufs into a KMS buffer using
the PRIME kernel interface.
If the driver does not support prime import, the method is skipped.
It has been tested with a Freescale I.MX6 board.
https://bugzilla.gnome.org/show_bug.cgi?id=761059
This is simple video sink that use libdrm/libkms API to render frames.
The element uses planes to render through drmModeSetPlane().
It has been tested in an Exynos4412 board and in a Freescale I.MX6 board.
https://bugzilla.gnome.org/show_bug.cgi?id=761059
