Before we only started it when either:
- there is no send RTP stream
or
- we received an RTP packet for sending
This could mean that if the send RTP pads are connected but never receive any
RTP data, and the same session is also used for receiving RTP/RTCP, we would
never start the RTCP thread and would never send RTCP for the receiving part
of the session.
This can be reproduced with a pipeline like:
gst-launch-1.0 rtpbin name=rtpbin \
udpsrc port=5000 ! "application/x-rtp, media=video, clock-rate=90000, encoding-name=H264" ! rtpbin.recv_rtp_sink_0 \
udpsrc port=5001 ! rtpbin.recv_rtcp_sink_0 \
rtpbin.send_rtcp_src_0 ! fakesink name=rtcp_fakesink silent=false async=false sync=false \
rtpbin.recv_rtp_src_0_2553225531_96 ! decodebin ! xvimagesink \
fakesrc ! valve drop=true ! rtpbin.send_rtp_sink_0 \
rtpbin.send_rtp_src_0 ! fakesink name=rtp_fakesink silent=false async=false sync=false -v
Before this change the rtcp_fakesink would never send RTCP for the receiving
part of the session (i.e. no receiver reports!), after the change it does.
And before and after this change it would send RTCP for the receiving part of
the session if the sender part was omitted (the last two lines).
* Fix critical when new tags are found after segment event has already
been sent.
* Send global tags before stream tags.
* Split sending of tags out of gst_matroska_demux_send_event() into its
own function.
https://bugzilla.gnome.org/show_bug.cgi?id=745973
Previously we advanced the in_data pointer by bps for every channel, and then
later again for block_size*bps. This caused us to be one sample further than
expected if an input buffer covered two analysis frames. And in the end lead
to completely bogus values reported by level.
https://bugzilla.gnome.org/show_bug.cgi?id=746065
These are outside the expected range of sequence numbers and should be
clipped, especially for RTSP they might belong to packets from before a seek
or a previous stream in general.
We need to set up the transport in any case, not just if we have a container
stream or a non-interleaved stream. Only if we have an interleaved stream and
are retrying, we should not set up the stream again.
https://bugzilla.gnome.org/show_bug.cgi?id=745599
Otherwise we will get not-negotiated later from rtpbin, and will never be able
to send RTCP packets back to the server. Note that error flow returns from the
RTCP pads are ignored, that's why it didn't fail more visible before.
This reverts commit 1591adf4cd.
https://bugzilla.gnome.org/show_bug.cgi?id=745586#c1:
It's the beginning of an implementation of RFC 2762, which is needed for
large multicast groups. The implementation is not yet complete but why
not leave what is there and implement RFC 2762 instead?
rtpsession declares an array of maps to store srrcs but only the
the key 0 is being used. This patch replaces the array of maps
for just one map and remove useless parameters in rtpsession
https://bugzilla.gnome.org/show_bug.cgi?id=745586
In gst_avi_demux_handle_src_query, there is not needed code.
We already check about stream is vbr or not at the upper line.
o, we don't need to check this condition becase stream is not
vbr 100% in this case.
https://bugzilla.gnome.org/show_bug.cgi?id=745276
Unlike many other seek flags, the KEY_UNIT seek
flag is not copied over into the GstSegment,
since it's only relevant for the seek itself,
so we need to pass it explicitly to the seek
handler here.
https://bugzilla.gnome.org/show_bug.cgi?id=745339
