The values of channel_mapping are copied by gst_codec_utils_opus_create_caps ()
but it doesn't free or take ownership of the g_new0 allocated memory. This
needs to be freed before going out of scope.
CID 1338692
If tsdemux never receives data for a stream, the corresponding pad will never
be added and stream->active will remain FALSE. When the stream is removed, the
pad will not be unreffed and will be leaked.
https://bugzilla.gnome.org/show_bug.cgi?id=757873
The tsdemux latency should always be added to the minimum
latency (which is always a valid clock time value). The
"cleanup" in commit a1f709c2 made it so that it would not
be added if upstream reported 0 as minimum latency (as
e.g. udpsrc would). This broke playback of live mpeg-ts
streaming in some cases, leading to playback stutter due
to a too-small configured latency for the pipeline.
https://bugzilla.gnome.org/show_bug.cgi?id=751508
The segment should start at first PTS, and the vairable name lower_pts
state so correctly. Though we where using the first DTS instead. This
could lead to small desynchronization of video stream.
https://bugzilla.gnome.org/show_bug.cgi?id=740575
Chinese broadcaster encapsulate AVS video codec into MPEG2-TS. They
use the stream_id 0x42 to identify AVS video streams. It should be noted
that this id is currently within the ISO reserved range, hence it's
utilisation is unofficial.
https://bugzilla.gnome.org/show_bug.cgi?id=727731
Timestamps should start at the segment start, rather than 0, so
we need to not subtract the first timestamp. This makes the sink
correctly account for running time when switching PMTs where a
stream starts not quite at zero, causing timing offsets that can
become noticeable and causing dropped frames after a few times.
If the stream which is about to be removed still has a ref on a tag list we
should drop it.
Fix a leak which was occasionally happening with the
validate.file.playback.change_state_intensive.tron_en_ge_aac_h264_ts scenario.
https://bugzilla.gnome.org/show_bug.cgi?id=748576
Such seeks are used to change playback rate and we do not want
to alter the position in that case, so we bypass the flush/seek
logic, and set things up so a new segment is scheduled to be
regenerated.
https://bugzilla.gnome.org/show_bug.cgi?id=735100
This will happen when the PMT changes, replacing streams with
new ones. In that case, we need to accumulate the running time
from the previous chain in the segment base.
https://bugzilla.gnome.org/show_bug.cgi?id=745102
Always update the segment and not only for accurate seeking and always
send a new segment event after seeks.
For non-accurate force a reset of our segment info to start from
where our seek led us as we don't need to be accurate
https://bugzilla.gnome.org/show_bug.cgi?id=743363
The flush is called on discont and we shouldn't output a new segment
each time a discont happens. So this commit remove the mark for a new
segment when flushing streams by propagating the 'hard' flag passed
on the flusing from the base class.
https://bugzilla.gnome.org/show_bug.cgi?id=743363
Signal sparse streams properly in stream-start event and force sending
of pending sticky events which have been stored on the pad already and
which otherwise would only be sent on the first buffer or serialized
event (which means very late in case of subtitle streams). Playsink in
playbin waits for stream-start or another serialized event, and if we
don't do this it will wait for the multiqueue to run full before
starting playback, which might take a couple of seconds.
https://bugzilla.gnome.org/show_bug.cgi?id=734040
All pads of a stream are now added at the beginning. In order to cope with
streams that don't get any data (forever or for a long time) we detect gaps
and push out GAP events when needed.
Cleanups and commenting by Jan Schmidt <jan@centricular.com>
https://bugzilla.gnome.org/show_bug.cgi?id=734040
If a discontinuity in the stream is detected, data is discarded until
a new PES starts. If the first packet after the discontinuity is also
the start of a PES, there is no reason to discard the packets.
https://bugzilla.gnome.org/show_bug.cgi?id=737569
It was previously a mix and match of both variants, introducing just too much
confusion.
The prefix are from now on:
* GstMpegts for structures and type names (and not GstMpegTs)
* gst_mpegts_ for functions (and not gst_mpeg_ts_)
* GST_MPEGTS_ for enums/flags (and not GST_MPEG_TS_)
* GST_TYPE_MPEGTS_ for types (and not GST_TYPE_MPEG_TS_)
The rationale for chosing that is:
* the namespace is shorter/direct (it's mpegts, not mpeg_ts nor mpeg-ts)
* the namespace is one word under Gst
* it's shorter (yah)
Co-Authored by: Thibault Saunier <tsaunier@gnome.org>
From a high level perspective, the new process for seeking h264
streams is as follows:
1) Rewind the stream until we find the first I-slice of a frame,
and mark its offset in the stream.
2) Rewind the stream until we find SPS and PPS informations,
to make sure the subsequent parser is up to date.
3) Accumulate optionnal SEI NAL units on the way.
4) Push the SPS, PPS and SEI units before the new keyframe.
https://bugzilla.gnome.org/show_bug.cgi?id=675132
