Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
/* GStreamer
|
|
|
|
* Copyright (C) <2006> Eric Jonas <jonas@mit.edu>
|
|
|
|
* Copyright (C) <2006> Antoine Tremblay <hexa00@gmail.com>
|
|
|
|
*
|
|
|
|
* This library is free software; you can redistribute it and/or
|
|
|
|
* modify it under the terms of the GNU Library General Public
|
|
|
|
* License as published by the Free Software Foundation; either
|
|
|
|
* version 2 of the License, or (at your option) any later version.
|
|
|
|
*
|
|
|
|
* This library is distributed in the hope that it will be useful,
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
|
|
* Library General Public License for more details.
|
|
|
|
*
|
|
|
|
* You should have received a copy of the GNU Library General Public
|
|
|
|
* License along with this library; if not, write to the
|
2012-11-03 20:38:00 +00:00
|
|
|
* Free Software Foundation, Inc., 51 Franklin St, Fifth Floor,
|
|
|
|
* Boston, MA 02110-1301, USA.
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
*/
|
|
|
|
|
|
|
|
/**
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
* SECTION:element-dc1394src
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
*
|
2008-01-22 12:06:19 +00:00
|
|
|
* Source for IIDC (Instrumentation & Industrial Digital Camera) firewire
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
* cameras. If several cameras are connected to the system, the desired one
|
|
|
|
* can be selected by its GUID and an optional unit number (most cameras are
|
|
|
|
* single unit and do not require it). The frame size, rate and format are set
|
|
|
|
* from capabilities. Although the IIDC specification includes a raw video
|
|
|
|
* mode, many cameras use mono video modes to capture in Bayer format.
|
|
|
|
* Thus, for each mono video mode supported by a camera, both gray raw and Bayer
|
|
|
|
* corresponding video formats are exposed in the capabilities.
|
|
|
|
* The Bayer pattern is left unspecified.
|
|
|
|
*
|
2008-06-13 11:59:23 +00:00
|
|
|
* <refsect2>
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
* <title>Example launch lines</title>
|
|
|
|
* |[
|
|
|
|
* gst-launch-1.0 -v dc1394src ! videoconvert ! autovideosink
|
|
|
|
* ]| Capture and display frames from the first camera available in the system.
|
2008-06-13 11:59:23 +00:00
|
|
|
* |[
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
* gst-launch-1.0 dc1394src guid=00074813004DF937 \
|
|
|
|
* ! "video/x-bayer,format=gbrg,width=1280,height=960,framerate=15/2" \
|
|
|
|
* ! bayer2rgb ! videoconvert ! autovideosink
|
|
|
|
* ]| Capture and display frames from a specific camera in the desired format.
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
* </refsect2>
|
|
|
|
*/
|
|
|
|
|
|
|
|
#ifdef HAVE_CONFIG_H
|
|
|
|
#include "config.h"
|
|
|
|
#endif
|
2016-06-07 13:50:50 +00:00
|
|
|
#include "gstdc1394src.h"
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
#include <gst/video/video.h>
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_CATEGORY_STATIC (dc1394_debug);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
#define GST_CAT_DEFAULT dc1394_debug
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
enum
|
|
|
|
{
|
|
|
|
PROP_0,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
PROP_CAMERA_GUID,
|
|
|
|
PROP_CAMERA_UNIT,
|
|
|
|
PROP_ISO_SPEED,
|
|
|
|
PROP_DMA_BUFFER_SIZE
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
#define GST_TYPE_DC1394_ISO_SPEED (gst_dc1394_iso_speed_get_type ())
|
|
|
|
static GType
|
|
|
|
gst_dc1394_iso_speed_get_type (void)
|
|
|
|
{
|
|
|
|
static const GEnumValue iso_speeds[] = {
|
|
|
|
{100, "DC1394 ISO speed 100", "100"},
|
|
|
|
{200, "DC1394 ISO speed 200", "200"},
|
|
|
|
{400, "DC1394 ISO speed 400", "400"},
|
|
|
|
{800, "DC1394 ISO speed 800", "800"},
|
|
|
|
{1600, "DC1394 ISO speed 1600", "1600"},
|
|
|
|
{3200, "DC1394 ISO speed 3200", "3200"},
|
|
|
|
{0, NULL, NULL}
|
|
|
|
};
|
|
|
|
static GType type = 0;
|
|
|
|
|
|
|
|
if (!type) {
|
|
|
|
type = g_enum_register_static ("GstDC1394ISOSpeed", iso_speeds);
|
|
|
|
}
|
|
|
|
return type;
|
|
|
|
}
|
|
|
|
|
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
#define gst_dc1394_src_parent_class parent_class
|
|
|
|
G_DEFINE_TYPE (GstDC1394Src, gst_dc1394_src, GST_TYPE_PUSH_SRC);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
static void gst_dc1394_src_set_property (GObject * object, guint prop_id,
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
const GValue * value, GParamSpec * pspec);
|
2016-06-07 13:50:50 +00:00
|
|
|
static void gst_dc1394_src_get_property (GObject * object, guint prop_id,
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
GValue * value, GParamSpec * pspec);
|
2016-06-07 13:50:50 +00:00
|
|
|
static gboolean gst_dc1394_src_start (GstBaseSrc * bsrc);
|
|
|
|
static gboolean gst_dc1394_src_stop (GstBaseSrc * bsrc);
|
|
|
|
static gboolean gst_dc1394_src_set_caps (GstBaseSrc * bsrc, GstCaps * caps);
|
|
|
|
static GstCaps *gst_dc1394_src_get_caps (GstBaseSrc * bsrc, GstCaps * filter);
|
|
|
|
static GstFlowReturn gst_dc1394_src_create (GstPushSrc * psrc,
|
|
|
|
GstBuffer ** buffer);
|
|
|
|
|
|
|
|
static void gst_dc1394_src_set_prop_camera_guid (GstDC1394Src * src,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
const gchar * guid);
|
2016-06-07 13:50:50 +00:00
|
|
|
static gchar *gst_dc1394_src_get_prop_camera_guid (GstDC1394Src * src);
|
|
|
|
static void gst_dc1394_src_set_prop_camera_unit (GstDC1394Src * src, gint unit);
|
|
|
|
static gint gst_dc1394_src_get_prop_camera_unit (GstDC1394Src * src);
|
|
|
|
static void gst_dc1394_src_set_prop_iso_speed (GstDC1394Src * src, guint speed);
|
|
|
|
static guint gst_dc1394_src_get_prop_iso_speed (GstDC1394Src * src);
|
|
|
|
static void gst_dc1394_src_set_prop_dma_buffer_size (GstDC1394Src * src,
|
|
|
|
guint size);
|
|
|
|
static guint gst_dc1394_src_get_prop_dma_buffer_size (GstDC1394Src * src);
|
|
|
|
static gboolean gst_dc1394_src_open_cam (GstDC1394Src * src);
|
|
|
|
static void gst_dc1394_src_close_cam (GstDC1394Src * src);
|
|
|
|
static gboolean gst_dc1394_src_start_cam (GstDC1394Src * src);
|
|
|
|
static gboolean gst_dc1394_src_stop_cam (GstDC1394Src * src);
|
|
|
|
static gboolean gst_dc1394_src_set_cam_caps (GstDC1394Src * src,
|
|
|
|
GstCaps * caps);
|
|
|
|
static GstCaps *gst_dc1394_src_get_cam_caps (GstDC1394Src * src);
|
|
|
|
static GstCaps *gst_dc1394_src_get_all_caps (void);
|
|
|
|
|
|
|
|
static GstCaps *gst_dc1394_src_build_caps (const dc1394color_codings_t *
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
supported_codings, const dc1394framerates_t * supported_rates,
|
|
|
|
guint width_min, guint width_max, guint width_step, guint height_min,
|
|
|
|
guint height_max, guint height_step);
|
2016-06-07 13:50:50 +00:00
|
|
|
static gboolean gst_dc1394_src_parse_caps (const GstCaps * caps,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
dc1394color_codings_t * color_codings, dc1394framerate_t * rate,
|
|
|
|
gdouble * rate_decimal, guint * width, guint * height);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_class_init (GstDC1394SrcClass * klass)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
|
|
|
GObjectClass *gobject_class;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GstElementClass *element_class;
|
|
|
|
GstBaseSrcClass *basesrc_class;
|
|
|
|
GstPushSrcClass *pushsrc_class;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
gobject_class = G_OBJECT_CLASS (klass);
|
|
|
|
element_class = GST_ELEMENT_CLASS (klass);
|
|
|
|
basesrc_class = GST_BASE_SRC_CLASS (klass);
|
|
|
|
pushsrc_class = GST_PUSH_SRC_CLASS (klass);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
gobject_class->set_property = gst_dc1394_src_set_property;
|
|
|
|
gobject_class->get_property = gst_dc1394_src_get_property;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
g_object_class_install_property (gobject_class, PROP_CAMERA_GUID,
|
|
|
|
g_param_spec_string ("guid", "Camera GUID",
|
|
|
|
"The hexadecimal representation of the GUID of the camera"
|
|
|
|
" (use first camera available if null)",
|
|
|
|
NULL,
|
|
|
|
G_PARAM_STATIC_STRINGS | G_PARAM_READWRITE |
|
|
|
|
GST_PARAM_MUTABLE_READY));
|
|
|
|
g_object_class_install_property (gobject_class, PROP_CAMERA_UNIT,
|
|
|
|
g_param_spec_int ("unit", "Camera unit",
|
|
|
|
"The unit number of the camera (-1 if no unit number is used)",
|
|
|
|
-1, G_MAXINT, -1,
|
|
|
|
G_PARAM_STATIC_STRINGS | G_PARAM_READWRITE |
|
|
|
|
GST_PARAM_MUTABLE_READY));
|
|
|
|
g_object_class_install_property (gobject_class, PROP_ISO_SPEED,
|
|
|
|
g_param_spec_enum ("iso", "ISO bandwidth",
|
|
|
|
"The ISO bandwidth in Mbps",
|
|
|
|
GST_TYPE_DC1394_ISO_SPEED, 400,
|
|
|
|
G_PARAM_STATIC_STRINGS | G_PARAM_READWRITE |
|
|
|
|
GST_PARAM_MUTABLE_READY));
|
|
|
|
g_object_class_install_property (gobject_class, PROP_DMA_BUFFER_SIZE,
|
|
|
|
g_param_spec_uint ("dma", "DMA ring buffer size",
|
|
|
|
"The number of frames in the Direct Memory Access ring buffer",
|
|
|
|
1, G_MAXUINT, 10,
|
|
|
|
G_PARAM_STATIC_STRINGS | G_PARAM_READWRITE |
|
|
|
|
GST_PARAM_MUTABLE_READY));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
gst_element_class_set_static_metadata (element_class,
|
|
|
|
"1394 IIDC Video Source", "Source/Video",
|
|
|
|
"libdc1394 based source for IIDC cameras",
|
|
|
|
"Antoine Tremblay <hexa00@gmail.com>");
|
|
|
|
gst_element_class_add_pad_template (element_class,
|
|
|
|
gst_pad_template_new ("src", GST_PAD_SRC, GST_PAD_ALWAYS,
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_all_caps ()));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
basesrc_class->start = GST_DEBUG_FUNCPTR (gst_dc1394_src_start);
|
|
|
|
basesrc_class->stop = GST_DEBUG_FUNCPTR (gst_dc1394_src_stop);
|
|
|
|
basesrc_class->set_caps = GST_DEBUG_FUNCPTR (gst_dc1394_src_set_caps);
|
|
|
|
basesrc_class->get_caps = GST_DEBUG_FUNCPTR (gst_dc1394_src_get_caps);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
pushsrc_class->create = GST_DEBUG_FUNCPTR (gst_dc1394_src_create);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_init (GstDC1394Src * src)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
src->guid = -1;
|
|
|
|
src->unit = -1;
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_400;
|
|
|
|
src->dma_buffer_size = 10;
|
|
|
|
src->dc1394 = NULL;
|
|
|
|
src->camera = NULL;
|
|
|
|
src->caps = NULL;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
gst_base_src_set_live (GST_BASE_SRC (src), TRUE);
|
|
|
|
gst_base_src_set_format (GST_BASE_SRC (src), GST_FORMAT_TIME);
|
|
|
|
gst_base_src_set_do_timestamp (GST_BASE_SRC (src), TRUE);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
2011-05-26 07:22:31 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_property (GObject * object, guint prop_id, GValue * value,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GParamSpec * pspec)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (object);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
switch (prop_id) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case PROP_CAMERA_GUID:
|
2016-06-07 13:50:50 +00:00
|
|
|
g_value_take_string (value, gst_dc1394_src_get_prop_camera_guid (src));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case PROP_CAMERA_UNIT:
|
2016-06-07 13:50:50 +00:00
|
|
|
g_value_set_int (value, gst_dc1394_src_get_prop_camera_unit (src));
|
2009-12-08 20:37:03 +00:00
|
|
|
break;
|
|
|
|
case PROP_ISO_SPEED:
|
2016-06-07 13:50:50 +00:00
|
|
|
g_value_set_enum (value, gst_dc1394_src_get_prop_iso_speed (src));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
break;
|
|
|
|
case PROP_DMA_BUFFER_SIZE:
|
2016-06-07 13:50:50 +00:00
|
|
|
g_value_set_uint (value, gst_dc1394_src_get_prop_dma_buffer_size (src));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
break;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
default:
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
G_OBJECT_WARN_INVALID_PROPERTY_ID (object, prop_id, pspec);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_property (GObject * object,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
guint prop_id, const GValue * value, GParamSpec * pspec)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (object);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
switch (prop_id) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case PROP_CAMERA_GUID:
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_camera_guid (src, g_value_get_string (value));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case PROP_CAMERA_UNIT:
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_camera_unit (src, g_value_get_int (value));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
2009-12-08 20:37:03 +00:00
|
|
|
case PROP_ISO_SPEED:
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_iso_speed (src, g_value_get_enum (value));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
break;
|
|
|
|
case PROP_DMA_BUFFER_SIZE:
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_dma_buffer_size (src, g_value_get_uint (value));
|
2009-12-08 20:37:03 +00:00
|
|
|
break;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
default:
|
|
|
|
G_OBJECT_WARN_INVALID_PROPERTY_ID (object, prop_id, pspec);
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_start (GstBaseSrc * bsrc)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (bsrc);
|
|
|
|
return gst_dc1394_src_open_cam (src);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_stop (GstBaseSrc * bsrc)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (bsrc);
|
|
|
|
if (!gst_dc1394_src_stop_cam (src))
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return FALSE;
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_close_cam (src);
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return TRUE;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static GstCaps *
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_caps (GstBaseSrc * bsrc, GstCaps * filter)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GstCaps *caps, *ret;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (bsrc);
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (src->camera) {
|
2016-06-07 13:50:50 +00:00
|
|
|
caps = gst_dc1394_src_get_cam_caps (src);
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
} else {
|
2016-06-07 13:50:50 +00:00
|
|
|
caps = gst_dc1394_src_get_all_caps ();
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (caps && filter) {
|
|
|
|
ret = gst_caps_intersect_full (filter, caps, GST_CAPS_INTERSECT_FIRST);
|
|
|
|
gst_caps_unref (caps);
|
|
|
|
} else {
|
|
|
|
ret = caps;
|
|
|
|
}
|
|
|
|
return ret;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_caps (GstBaseSrc * bsrc, GstCaps * caps)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (bsrc);
|
|
|
|
return gst_dc1394_src_stop_cam (src)
|
|
|
|
&& gst_dc1394_src_set_cam_caps (src, caps)
|
|
|
|
&& gst_dc1394_src_start_cam (src);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
static GstFlowReturn
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_create (GstPushSrc * psrc, GstBuffer ** obuf)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
2016-06-07 13:50:50 +00:00
|
|
|
GstDC1394Src *src;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GstBuffer *buffer;
|
|
|
|
dc1394video_frame_t *frame;
|
|
|
|
dc1394error_t ret;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
2016-06-07 13:50:50 +00:00
|
|
|
src = GST_DC1394_SRC (psrc);
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
buffer = NULL;
|
|
|
|
ret = dc1394_capture_dequeue (src->camera, DC1394_CAPTURE_POLICY_WAIT,
|
|
|
|
&frame);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, READ, (NULL),
|
|
|
|
("Could not dequeue frame: %s.", dc1394_error_get_string (ret)));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
goto error;
|
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
/*
|
|
|
|
* TODO: We could create the buffer by wrapping the image bytes in the frame
|
|
|
|
* (enqueing the frame in the notify function) to save the copy operation.
|
|
|
|
* It will only work if all the buffers are disposed before closing the camera
|
|
|
|
* when state changes from PAUSED to READY.
|
|
|
|
*/
|
|
|
|
buffer = gst_buffer_new_allocate (NULL, frame->image_bytes, NULL);
|
|
|
|
gst_buffer_fill (buffer, 0, frame->image, frame->image_bytes);
|
|
|
|
/*
|
|
|
|
* TODO: There is a field timestamp in the frame structure,
|
|
|
|
* It is not sure if it could be used as PTS or DTS:
|
|
|
|
* we are not sure if it comes from a monotonic clock,
|
|
|
|
* and it seems to be left undefined under MS Windows.
|
|
|
|
*/
|
|
|
|
ret = dc1394_capture_enqueue (src->camera, frame);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_WARNING (src, RESOURCE, READ, (NULL),
|
|
|
|
("Could not enqueue frame: %s.", dc1394_error_get_string (ret)));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
*obuf = buffer;
|
|
|
|
return GST_FLOW_OK;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
error:
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (buffer)
|
|
|
|
gst_buffer_unref (buffer);
|
|
|
|
return GST_FLOW_ERROR;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_camera_guid (GstDC1394Src * src, const gchar * guid)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
gchar *end;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!guid) {
|
|
|
|
GST_DEBUG_OBJECT (src, "Null camera GUID value: %s.",
|
|
|
|
"first camera available will be used");
|
|
|
|
src->guid = -1;
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
errno = 0;
|
|
|
|
src->guid = g_ascii_strtoull (guid, &end, 16);
|
|
|
|
if (errno == ERANGE || end == guid || *end != '\0') {
|
|
|
|
GST_ERROR_OBJECT (src, "Invalid camera GUID value: %s.", guid);
|
|
|
|
return;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gchar *
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_prop_camera_guid (GstDC1394Src * src)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
|
|
|
if (src->guid == -1) {
|
|
|
|
return NULL;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return g_strdup_printf ("%016" G_GINT64_MODIFIER "X", src->guid);
|
|
|
|
}
|
2008-02-26 05:54:26 +00:00
|
|
|
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_camera_unit (GstDC1394Src * src, gint unit)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
|
|
|
src->unit = unit;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
2007-06-29 15:23:34 +00:00
|
|
|
static gint
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_prop_camera_unit (GstDC1394Src * src)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return src->unit;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_iso_speed (GstDC1394Src * src, guint speed)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
switch (speed) {
|
|
|
|
case 100:
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_100;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case 200:
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_200;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case 400:
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_400;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case 800:
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_800;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case 1600:
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_1600;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case 3200:
|
|
|
|
src->iso_speed = DC1394_ISO_SPEED_3200;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
break;
|
|
|
|
default:
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_ERROR_OBJECT (src, "Invalid ISO speed value: %d.", speed);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static guint
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_prop_iso_speed (GstDC1394Src * src)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
switch (src->iso_speed) {
|
|
|
|
case DC1394_ISO_SPEED_100:
|
|
|
|
return 100;
|
|
|
|
case DC1394_ISO_SPEED_200:
|
|
|
|
return 200;
|
|
|
|
case DC1394_ISO_SPEED_400:
|
|
|
|
return 400;
|
|
|
|
case DC1394_ISO_SPEED_800:
|
|
|
|
return 800;
|
|
|
|
case DC1394_ISO_SPEED_1600:
|
|
|
|
return 1600;
|
|
|
|
case DC1394_ISO_SPEED_3200:
|
|
|
|
return 3200;
|
|
|
|
default: /* never reached */
|
|
|
|
return DC1394_ISO_SPEED_MIN - 1;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
2007-06-29 15:23:34 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_prop_dma_buffer_size (GstDC1394Src * src, guint size)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
src->dma_buffer_size = size;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static guint
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_prop_dma_buffer_size (GstDC1394Src * src)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return src->dma_buffer_size;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_open_cam (GstDC1394Src * src)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
dc1394camera_list_t *cameras;
|
|
|
|
dc1394error_t ret;
|
|
|
|
int number;
|
|
|
|
uint64_t guid;
|
2016-06-09 21:01:13 +00:00
|
|
|
int unit, i;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
|
|
|
src->dc1394 = dc1394_new ();
|
|
|
|
if (!src->dc1394) {
|
|
|
|
GST_ELEMENT_ERROR (src, LIBRARY, INIT, (NULL),
|
|
|
|
("Could not initialize dc1394 library."));
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
number = -1;
|
|
|
|
guid = -1;
|
|
|
|
unit = -1;
|
|
|
|
ret = dc1394_camera_enumerate (src->dc1394, &cameras);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, LIBRARY, FAILED, (NULL),
|
|
|
|
("Could not enumerate cameras: %s.", dc1394_error_get_string (ret)));
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
2016-06-09 21:01:13 +00:00
|
|
|
for (i = 0; i < cameras->num; i++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src, "Camera %2d is %016" G_GINT64_MODIFIER "X %d.",
|
|
|
|
i, cameras->ids[i].guid, cameras->ids[i].unit);
|
|
|
|
if ((src->guid == -1 || src->guid == cameras->ids[i].guid) &&
|
|
|
|
(src->unit == -1 || src->unit == cameras->ids[i].unit)) {
|
|
|
|
number = i;
|
|
|
|
guid = cameras->ids[i].guid;
|
|
|
|
unit = cameras->ids[i].unit;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
dc1394_camera_free_list (cameras);
|
|
|
|
if (number < 0) {
|
|
|
|
if (src->guid == -1) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, NOT_FOUND, (NULL),
|
|
|
|
("No cameras found."));
|
|
|
|
} else {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, NOT_FOUND, (NULL),
|
|
|
|
("Camera %016" G_GINT64_MODIFIER "X %d not found.",
|
|
|
|
src->guid, src->unit));
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
goto error;
|
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src, "Open camera %016" G_GINT64_MODIFIER "X %d.",
|
|
|
|
guid, unit);
|
|
|
|
src->camera = dc1394_camera_new_unit (src->dc1394, guid, unit);
|
|
|
|
if (!src->camera) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, OPEN_READ_WRITE, (NULL),
|
|
|
|
("Could not open camera %016" G_GINT64_MODIFIER "X %d.", guid, unit));
|
2008-02-26 05:54:26 +00:00
|
|
|
goto error;
|
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src,
|
|
|
|
"Camera %016" G_GINT64_MODIFIER "X %d opened: \"%s %s\".",
|
|
|
|
src->camera->guid, src->camera->unit,
|
|
|
|
src->camera->vendor, src->camera->model);
|
|
|
|
|
|
|
|
if (src->iso_speed > DC1394_ISO_SPEED_400) {
|
|
|
|
ret = dc1394_video_set_operation_mode (src->camera,
|
|
|
|
DC1394_OPERATION_MODE_1394B);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not set 1394B operation mode: %s.",
|
|
|
|
dc1394_error_get_string (ret)));
|
|
|
|
goto error;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
ret = dc1394_video_set_iso_speed (src->camera, src->iso_speed);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not set ISO speed %d: %s.", src->iso_speed,
|
|
|
|
dc1394_error_get_string (ret)));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
goto error;
|
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return TRUE;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
error:
|
|
|
|
if (src->camera) {
|
|
|
|
dc1394_camera_free (src->camera);
|
|
|
|
src->camera = NULL;
|
|
|
|
}
|
|
|
|
if (src->dc1394) {
|
|
|
|
dc1394_free (src->dc1394);
|
|
|
|
src->dc1394 = NULL;
|
|
|
|
}
|
|
|
|
return FALSE;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static void
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_close_cam (GstDC1394Src * src)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
|
|
|
GST_DEBUG_OBJECT (src,
|
|
|
|
"Close camera %016" G_GINT64_MODIFIER "X %d: \"%s %s\".",
|
|
|
|
src->camera->guid, src->camera->unit,
|
|
|
|
src->camera->vendor, src->camera->model);
|
|
|
|
if (src->caps) {
|
|
|
|
gst_caps_unref (src->caps);
|
|
|
|
src->caps = NULL;
|
|
|
|
}
|
|
|
|
dc1394_camera_free (src->camera);
|
|
|
|
src->camera = NULL;
|
|
|
|
dc1394_free (src->dc1394);
|
|
|
|
src->dc1394 = NULL;
|
|
|
|
GST_DEBUG_OBJECT (src, "Camera closed.");
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_start_cam (GstDC1394Src * src)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
|
|
|
dc1394error_t ret;
|
|
|
|
dc1394switch_t status;
|
2016-06-09 21:01:13 +00:00
|
|
|
guint trials;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src, "Setup capture with a DMA buffer of %d frames",
|
|
|
|
src->dma_buffer_size);
|
|
|
|
ret = dc1394_capture_setup (src->camera, src->dma_buffer_size,
|
|
|
|
DC1394_CAPTURE_FLAGS_DEFAULT);
|
|
|
|
if (ret == DC1394_NO_BANDWIDTH) {
|
|
|
|
GST_DEBUG_OBJECT (src,
|
|
|
|
"Could not setup capture with available ISO bandwidth,"
|
|
|
|
"releasing channels and bandwidth and retrying...");
|
|
|
|
ret = dc1394_iso_release_all (src->camera);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_WARNING (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not release ISO channels and bandwidth: %s",
|
|
|
|
dc1394_error_get_string (ret)));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
ret = dc1394_capture_setup (src->camera, src->dma_buffer_size,
|
|
|
|
DC1394_CAPTURE_FLAGS_DEFAULT);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not setup capture: %s", dc1394_error_get_string (ret)));
|
|
|
|
goto error_capture;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
/*
|
|
|
|
* TODO: dc1394_capture_setup/stop can start/stop the transmission
|
|
|
|
* when called with DC1394_CAPTURE_FLAGS_AUTO_ISO in the flags.
|
|
|
|
* The repeated trials check is a leftover of the original code,
|
|
|
|
* and might not be needed.
|
|
|
|
*/
|
|
|
|
GST_DEBUG_OBJECT (src, "Enable camera transmission.");
|
|
|
|
ret = dc1394_video_set_transmission (src->camera, DC1394_ON);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not set transmission status: %s.",
|
|
|
|
dc1394_error_get_string (ret)));
|
|
|
|
goto error_transmission;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
ret = dc1394_video_get_transmission (src->camera, &status);
|
2016-06-09 21:01:13 +00:00
|
|
|
for (trials = 10;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
(trials > 0) && !(ret == DC1394_SUCCESS && status == DC1394_ON);
|
|
|
|
trials--) {
|
|
|
|
GST_DEBUG_OBJECT (src,
|
|
|
|
"Wait for camera to start transmission (%d trials left).", trials);
|
|
|
|
g_usleep (50000);
|
|
|
|
ret = dc1394_video_get_transmission (src->camera, &status);
|
2008-02-26 05:54:26 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!(ret == DC1394_SUCCESS && status == DC1394_ON)) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not get positive transmission status: %s.",
|
|
|
|
dc1394_error_get_string (ret)));
|
|
|
|
goto error_transmission;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src, "Capture successfully started.");
|
|
|
|
return TRUE;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
error_transmission:
|
|
|
|
ret = dc1394_capture_stop (src->camera);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_WARNING (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not stop capture: %s.", dc1394_error_get_string (ret)));
|
|
|
|
}
|
|
|
|
error_capture:
|
|
|
|
return FALSE;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
2007-06-29 15:23:34 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_stop_cam (GstDC1394Src * src)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
dc1394error_t ret;
|
|
|
|
|
|
|
|
GST_DEBUG_OBJECT (src, "Disable camera transmission.");
|
|
|
|
ret = dc1394_video_set_transmission (src->camera, DC1394_OFF);
|
|
|
|
if (ret != DC1394_SUCCESS) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not set transmission status: %s.",
|
|
|
|
dc1394_error_get_string (ret)));
|
|
|
|
return FALSE;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src, "Clear capture resources.");
|
|
|
|
ret = dc1394_capture_stop (src->camera);
|
|
|
|
if (ret != DC1394_SUCCESS && ret != DC1394_CAPTURE_IS_NOT_SET) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, FAILED, (NULL),
|
|
|
|
("Could not clear capture: %s.", dc1394_error_get_string (ret)));
|
|
|
|
return FALSE;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
switch (ret) {
|
|
|
|
case DC1394_CAPTURE_IS_NOT_SET:
|
|
|
|
GST_DEBUG_OBJECT (src, "Capture was not set up.");
|
2009-12-08 20:37:03 +00:00
|
|
|
break;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
case DC1394_SUCCESS:
|
|
|
|
GST_DEBUG_OBJECT (src, "Capture successfully stopped.");
|
2009-12-08 20:37:03 +00:00
|
|
|
break;
|
|
|
|
default:
|
|
|
|
break;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return TRUE;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_set_cam_caps (GstDC1394Src * src, GstCaps * caps)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
|
|
|
GstCaps *mode_caps;
|
|
|
|
gboolean ok, supported;
|
|
|
|
dc1394video_modes_t supported_modes;
|
|
|
|
dc1394video_mode_t mode;
|
|
|
|
dc1394color_codings_t supported_codings;
|
|
|
|
dc1394color_coding_t coding;
|
|
|
|
dc1394framerates_t supported_rates;
|
|
|
|
dc1394framerate_t rate;
|
|
|
|
double rate_decimal;
|
|
|
|
uint64_t total_bytes;
|
|
|
|
uint32_t width, width_step, height, height_step;
|
2016-06-09 21:01:13 +00:00
|
|
|
guint m, c;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
|
|
|
ok = dc1394_video_get_supported_modes (src->camera,
|
|
|
|
&supported_modes) == DC1394_SUCCESS;
|
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not get supported modes."));
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
goto error;
|
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
supported = FALSE;
|
2016-06-09 21:01:13 +00:00
|
|
|
for (m = 0; m < supported_modes.num && !supported; m++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
mode = supported_modes.modes[m];
|
|
|
|
mode_caps = gst_caps_new_empty ();
|
|
|
|
if (dc1394_is_video_mode_scalable (mode)) {
|
|
|
|
ok &= dc1394_format7_get_color_codings (src->camera, mode,
|
|
|
|
&supported_codings) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_format7_get_max_image_size (src->camera, mode,
|
|
|
|
&width, &height) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_format7_get_unit_size (src->camera, mode,
|
|
|
|
&width_step, &height_step) == DC1394_SUCCESS;
|
|
|
|
} else {
|
|
|
|
ok &= dc1394_get_color_coding_from_video_mode (src->camera, mode,
|
|
|
|
&coding) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_get_image_size_from_video_mode (src->camera, mode,
|
|
|
|
&width, &height) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_video_get_supported_framerates (src->camera, mode,
|
|
|
|
&supported_rates) == DC1394_SUCCESS;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_WARNING (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not get video mode %d parameters.", mode));
|
|
|
|
} else if (dc1394_is_video_mode_scalable (mode)) {
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_caps_append (mode_caps,
|
|
|
|
gst_dc1394_src_build_caps (&supported_codings, NULL,
|
|
|
|
width_step, width, width_step, height_step, height, height_step));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
} else {
|
|
|
|
supported_codings.num = 1;
|
|
|
|
supported_codings.codings[0] = coding;
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_caps_append (mode_caps,
|
|
|
|
gst_dc1394_src_build_caps (&supported_codings, &supported_rates,
|
|
|
|
width, width, 1, height, height, 1));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
}
|
|
|
|
supported = gst_caps_can_intersect (caps, mode_caps);
|
|
|
|
gst_caps_unref (mode_caps);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
2016-06-07 13:50:50 +00:00
|
|
|
ok = supported && gst_dc1394_src_parse_caps (caps, &supported_codings, &rate,
|
|
|
|
&rate_decimal, &width, &height);
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Unsupported caps %" GST_PTR_FORMAT, caps));
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GST_DEBUG_OBJECT (src, "Set video mode %d.", mode);
|
|
|
|
ok = dc1394_video_set_mode (src->camera, mode) == DC1394_SUCCESS;
|
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not set video mode %d.", mode));
|
|
|
|
goto error;
|
|
|
|
}
|
|
|
|
if (dc1394_is_video_mode_scalable (mode)) {
|
|
|
|
ok = FALSE;
|
2016-06-09 21:01:13 +00:00
|
|
|
for (c = 0; c < supported_codings.num && !ok; c++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
coding = supported_codings.codings[c];
|
|
|
|
GST_DEBUG_OBJECT (src,
|
|
|
|
"Try format7 video mode %d with coding %d, size %d %d, and rate %.4f Hz.",
|
|
|
|
mode, coding, width, height, rate_decimal);
|
|
|
|
ok = (dc1394_format7_set_color_coding (src->camera, mode,
|
|
|
|
coding) == DC1394_SUCCESS)
|
|
|
|
&& (dc1394_format7_set_image_size (src->camera, mode,
|
|
|
|
width, height) == DC1394_SUCCESS)
|
|
|
|
&& (dc1394_format7_get_total_bytes (src->camera, mode,
|
|
|
|
&total_bytes) == DC1394_SUCCESS)
|
|
|
|
&& (dc1394_format7_set_packet_size (src->camera, mode,
|
|
|
|
total_bytes * rate_decimal * 0.000125) == DC1394_SUCCESS);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
} else {
|
|
|
|
GST_DEBUG_OBJECT (src, "Set fixed video mode %d rate %.4f Hz (%d).",
|
|
|
|
mode, rate_decimal, rate);
|
|
|
|
ok = dc1394_video_set_framerate (src->camera, rate) == DC1394_SUCCESS;
|
|
|
|
}
|
2016-06-09 21:01:13 +00:00
|
|
|
/* TODO: check feature framerate */
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not set video mode %d parameters.", mode));
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
return TRUE;
|
|
|
|
|
|
|
|
error:
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return FALSE;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GstCaps *
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_cam_caps (GstDC1394Src * src)
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
{
|
|
|
|
gboolean ok;
|
|
|
|
dc1394video_modes_t supported_modes;
|
|
|
|
dc1394video_mode_t mode;
|
|
|
|
dc1394color_codings_t supported_codings;
|
|
|
|
dc1394color_coding_t coding;
|
|
|
|
dc1394framerates_t supported_rates;
|
|
|
|
uint32_t width, width_step, height, height_step;
|
2016-06-09 21:01:13 +00:00
|
|
|
guint m;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
|
|
|
if (src->caps)
|
|
|
|
return gst_caps_ref (src->caps);
|
|
|
|
|
|
|
|
ok = dc1394_video_get_supported_modes (src->camera,
|
|
|
|
&supported_modes) == DC1394_SUCCESS;
|
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_ERROR (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not get supported modes."));
|
|
|
|
return NULL;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
src->caps = gst_caps_new_empty ();
|
2016-06-09 21:01:13 +00:00
|
|
|
for (m = 0; m < supported_modes.num; m++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
mode = supported_modes.modes[m];
|
|
|
|
if (dc1394_is_video_mode_scalable (mode)) {
|
|
|
|
ok &= dc1394_format7_get_color_codings (src->camera, mode,
|
|
|
|
&supported_codings) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_format7_get_max_image_size (src->camera, mode,
|
|
|
|
&width, &height) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_format7_get_unit_size (src->camera, mode,
|
|
|
|
&width_step, &height_step) == DC1394_SUCCESS;
|
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_WARNING (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not get format7 video mode %d parameters.", mode));
|
|
|
|
} else {
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_caps_append (src->caps,
|
|
|
|
gst_dc1394_src_build_caps (&supported_codings, NULL,
|
|
|
|
width_step, width, width_step, height_step, height,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
height_step));
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
ok &= dc1394_get_image_size_from_video_mode (src->camera, mode,
|
|
|
|
&width, &height) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_video_get_supported_framerates (src->camera, mode,
|
|
|
|
&supported_rates) == DC1394_SUCCESS;
|
|
|
|
ok &= dc1394_get_color_coding_from_video_mode (src->camera, mode,
|
|
|
|
&coding) == DC1394_SUCCESS;
|
|
|
|
if (!ok) {
|
|
|
|
GST_ELEMENT_WARNING (src, RESOURCE, SETTINGS, (NULL),
|
|
|
|
("Could not get fixed video mode %d parameters.", mode));
|
|
|
|
} else {
|
|
|
|
supported_codings.num = 1;
|
|
|
|
supported_codings.codings[0] = coding;
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_caps_append (src->caps,
|
|
|
|
gst_dc1394_src_build_caps (&supported_codings, &supported_rates,
|
|
|
|
width, width, 1, height, height, 1));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
GST_DEBUG_OBJECT (src, "Camera capabilities: \"%" GST_PTR_FORMAT "\".",
|
|
|
|
src->caps);
|
|
|
|
return gst_caps_ref (src->caps);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static GstCaps *
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_get_all_caps (void)
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
{
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
GstCaps *caps;
|
|
|
|
dc1394color_coding_t coding;
|
|
|
|
dc1394color_codings_t video_codings;
|
|
|
|
uint32_t width, height;
|
|
|
|
|
|
|
|
const dc1394color_codings_t supported_codings = { 7, {
|
|
|
|
/* DC1394_COLOR_CODING_RGB16S, DC1394_COLOR_CODING_RGB16, */
|
|
|
|
DC1394_COLOR_CODING_RGB8, DC1394_COLOR_CODING_YUV444,
|
|
|
|
DC1394_COLOR_CODING_YUV422, DC1394_COLOR_CODING_YUV411,
|
|
|
|
/* DC1394_COLOR_CODING_RAW16, DC1394_COLOR_CODING_MONO16S */
|
|
|
|
DC1394_COLOR_CODING_MONO16, DC1394_COLOR_CODING_RAW8,
|
|
|
|
DC1394_COLOR_CODING_MONO8}
|
|
|
|
};
|
|
|
|
const dc1394framerates_t all_rates = { 8, {
|
|
|
|
DC1394_FRAMERATE_1_875, DC1394_FRAMERATE_3_75, DC1394_FRAMERATE_7_5,
|
|
|
|
DC1394_FRAMERATE_15, DC1394_FRAMERATE_30, DC1394_FRAMERATE_60,
|
|
|
|
DC1394_FRAMERATE_120, DC1394_FRAMERATE_240}
|
|
|
|
};
|
2016-06-09 21:01:13 +00:00
|
|
|
dc1394video_mode_t mode;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
|
|
|
caps = gst_caps_new_empty ();
|
|
|
|
/* First caps for fixed video modes */
|
2016-06-09 21:01:13 +00:00
|
|
|
for (mode = DC1394_VIDEO_MODE_MIN; mode < DC1394_VIDEO_MODE_EXIF; mode++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
dc1394_get_image_size_from_video_mode (NULL, mode, &width, &height);
|
|
|
|
dc1394_get_color_coding_from_video_mode (NULL, mode, &coding);
|
|
|
|
video_codings.codings[0] = coding;
|
|
|
|
video_codings.num = 1;
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_caps_append (caps,
|
|
|
|
gst_dc1394_src_build_caps (&video_codings, &all_rates,
|
|
|
|
width, width, 1, height, height, 1));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
}
|
|
|
|
/* Then caps for Format 7 modes */
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_caps_append (caps,
|
|
|
|
gst_dc1394_src_build_caps (&supported_codings, NULL,
|
|
|
|
1, G_MAXINT, 1, 1, G_MAXINT, 1));
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
return caps;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static GstCaps *
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_build_caps (const dc1394color_codings_t * supported_codings,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
const dc1394framerates_t * supported_rates,
|
|
|
|
uint32_t width_min, uint32_t width_max, uint32_t width_step,
|
|
|
|
uint32_t height_min, uint32_t height_max, uint32_t height_step)
|
|
|
|
{
|
|
|
|
GstCaps *caps;
|
|
|
|
GstStructure *structure;
|
|
|
|
GstVideoFormat video_format;
|
|
|
|
dc1394color_coding_t coding;
|
|
|
|
dc1394framerate_t rate;
|
|
|
|
GValue format = { 0 };
|
|
|
|
GValue formats = { 0 };
|
|
|
|
GValue width = { 0 };
|
|
|
|
GValue widths = { 0 };
|
|
|
|
GValue height = { 0 };
|
|
|
|
GValue heights = { 0 };
|
|
|
|
GValue framerate = { 0 };
|
|
|
|
GValue framerates = { 0 };
|
2016-06-09 21:01:13 +00:00
|
|
|
guint c, w, h, r;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
|
|
|
caps = gst_caps_new_empty ();
|
2016-06-09 21:01:13 +00:00
|
|
|
for (c = 0; c < supported_codings->num; c++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
coding = supported_codings->codings[c];
|
|
|
|
switch (coding) {
|
|
|
|
case DC1394_COLOR_CODING_MONO8:
|
|
|
|
video_format = GST_VIDEO_FORMAT_GRAY8;
|
|
|
|
break;
|
|
|
|
case DC1394_COLOR_CODING_YUV411:
|
|
|
|
video_format = GST_VIDEO_FORMAT_IYU1;
|
|
|
|
break;
|
|
|
|
case DC1394_COLOR_CODING_YUV422:
|
|
|
|
video_format = GST_VIDEO_FORMAT_UYVY;
|
|
|
|
break;
|
|
|
|
case DC1394_COLOR_CODING_YUV444:
|
|
|
|
video_format = GST_VIDEO_FORMAT_IYU2;
|
|
|
|
break;
|
|
|
|
case DC1394_COLOR_CODING_RGB8:
|
|
|
|
video_format = GST_VIDEO_FORMAT_RGB;
|
|
|
|
break;
|
|
|
|
case DC1394_COLOR_CODING_RAW8:
|
|
|
|
video_format = GST_VIDEO_FORMAT_UNKNOWN; /* GST_BAYER_FORMAT_XXXX8 */
|
|
|
|
break;
|
|
|
|
case DC1394_COLOR_CODING_MONO16:
|
|
|
|
video_format = GST_VIDEO_FORMAT_GRAY16_BE;
|
|
|
|
break;
|
|
|
|
/*
|
|
|
|
* The following formats do not exist in Gstreamer:
|
|
|
|
*case DC1394_COLOR_CODING_RGB16: // Unsigned RGB 16 bits per channel
|
|
|
|
* video_format = GST_VIDEO_FORMAT_RGB48;
|
|
|
|
* break;
|
|
|
|
*case DC1394_COLOR_CODING_MONO16S: // Signed grayscale 16 bits
|
|
|
|
* video_format = GST_VIDEO_FORMAT_GRAY16_BE_SIGNED;
|
|
|
|
* break;
|
|
|
|
*case DC1394_COLOR_CODING_RGB16S: // Signed RGB 16 bits per channel
|
|
|
|
* video_format = GST_VIDEO_FORMAT_RGB48_SIGNED;
|
|
|
|
* break;
|
|
|
|
*case DC1394_COLOR_CODING_RAW16: // Raw sensor output (bayer) 16 bits
|
|
|
|
* video_format = GST_VIDEO_FORMAT_UNKNOWN; // GST_BAYER_FORMAT_XXXX16_BE
|
|
|
|
* break;
|
|
|
|
*/
|
|
|
|
default:
|
|
|
|
video_format = GST_VIDEO_FORMAT_UNKNOWN;
|
|
|
|
GST_DEBUG ("unsupported dc1394 video coding %d", coding);
|
|
|
|
}
|
|
|
|
if (video_format != GST_VIDEO_FORMAT_UNKNOWN) {
|
|
|
|
g_value_init (&formats, G_TYPE_STRING);
|
|
|
|
g_value_set_string (&formats, gst_video_format_to_string (video_format));
|
|
|
|
structure = gst_structure_new_empty ("video/x-raw");
|
|
|
|
gst_structure_set_value (structure, "format", &formats);
|
|
|
|
gst_caps_append_structure (caps, structure);
|
|
|
|
g_value_unset (&formats);
|
|
|
|
}
|
|
|
|
if (coding == DC1394_COLOR_CODING_MONO8 ||
|
|
|
|
coding == DC1394_COLOR_CODING_RAW8) {
|
|
|
|
g_value_init (&formats, GST_TYPE_LIST);
|
|
|
|
g_value_init (&format, G_TYPE_STRING);
|
|
|
|
g_value_set_static_string (&format, "bggr");
|
|
|
|
gst_value_list_append_value (&formats, &format);
|
|
|
|
g_value_set_static_string (&format, "rggb");
|
|
|
|
gst_value_list_append_value (&formats, &format);
|
|
|
|
g_value_set_static_string (&format, "grbg");
|
|
|
|
gst_value_list_append_value (&formats, &format);
|
|
|
|
g_value_set_static_string (&format, "gbrg");
|
|
|
|
gst_value_list_append_value (&formats, &format);
|
|
|
|
structure = gst_structure_new_empty ("video/x-bayer");
|
|
|
|
gst_structure_set_value (structure, "format", &formats);
|
|
|
|
gst_caps_append_structure (caps, structure);
|
|
|
|
g_value_unset (&format);
|
|
|
|
g_value_unset (&formats);
|
|
|
|
}
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (width_min == width_max) {
|
|
|
|
g_value_init (&widths, G_TYPE_INT);
|
|
|
|
g_value_set_int (&widths, width_min);
|
|
|
|
} else if (width_step == 1) {
|
|
|
|
g_value_init (&widths, GST_TYPE_INT_RANGE);
|
|
|
|
gst_value_set_int_range (&widths, width_min, width_max);
|
|
|
|
} else {
|
|
|
|
g_value_init (&widths, GST_TYPE_LIST);
|
|
|
|
g_value_init (&width, G_TYPE_INT);
|
2016-06-09 21:01:13 +00:00
|
|
|
for (w = width_min; w <= width_max; w += width_step) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
g_value_set_int (&width, w);
|
|
|
|
gst_value_list_append_value (&widths, &width);
|
|
|
|
}
|
|
|
|
g_value_unset (&width);
|
|
|
|
}
|
|
|
|
if (height_min == height_max) {
|
|
|
|
g_value_init (&heights, G_TYPE_INT);
|
|
|
|
g_value_set_int (&heights, height_min);
|
|
|
|
} else if (height_step == 1) {
|
|
|
|
g_value_init (&heights, GST_TYPE_INT_RANGE);
|
|
|
|
gst_value_set_int_range (&heights, height_min, height_max);
|
|
|
|
} else {
|
|
|
|
g_value_init (&heights, GST_TYPE_LIST);
|
|
|
|
g_value_init (&height, G_TYPE_INT);
|
2016-06-09 21:01:13 +00:00
|
|
|
for (h = height_min; h <= height_max; h += height_step) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
g_value_set_int (&height, h);
|
|
|
|
gst_value_list_append_value (&heights, &height);
|
|
|
|
}
|
|
|
|
g_value_unset (&height);
|
|
|
|
}
|
|
|
|
gst_caps_set_value (caps, "width", &widths);
|
|
|
|
gst_caps_set_value (caps, "height", &heights);
|
|
|
|
g_value_unset (&widths);
|
|
|
|
g_value_unset (&heights);
|
|
|
|
|
|
|
|
if (supported_rates) {
|
|
|
|
g_value_init (&framerates, GST_TYPE_LIST);
|
|
|
|
g_value_init (&framerate, GST_TYPE_FRACTION);
|
2016-06-09 21:01:13 +00:00
|
|
|
for (r = 0; r < supported_rates->num; r++) {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
rate = supported_rates->framerates[r];
|
|
|
|
switch (rate) {
|
|
|
|
case DC1394_FRAMERATE_1_875:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 128);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_3_75:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 64);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_7_5:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 32);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_15:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 16);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_30:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 8);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_60:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 4);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_120:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 2);
|
|
|
|
break;
|
|
|
|
case DC1394_FRAMERATE_240:
|
|
|
|
gst_value_set_fraction (&framerate, 240, 1);
|
|
|
|
break;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
gst_value_list_append_value (&framerates, &framerate);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
g_value_unset (&framerate);
|
|
|
|
} else {
|
|
|
|
g_value_init (&framerates, GST_TYPE_FRACTION_RANGE);
|
|
|
|
gst_value_set_fraction_range_full (&framerates, 1, G_MAXINT, G_MAXINT, 1);
|
|
|
|
}
|
|
|
|
gst_caps_set_value (caps, "framerate", &framerates);
|
|
|
|
g_value_unset (&framerates);
|
|
|
|
return caps;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
static gboolean
|
2016-06-07 13:50:50 +00:00
|
|
|
gst_dc1394_src_parse_caps (const GstCaps * caps,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
dc1394color_codings_t * color_codings,
|
|
|
|
dc1394framerate_t * rate, double *rate_decimal,
|
|
|
|
uint32_t * width, uint32_t * height)
|
|
|
|
{
|
|
|
|
const GstStructure *structure;
|
|
|
|
const gchar *format;
|
|
|
|
gint w, h, num, den;
|
|
|
|
gdouble dec;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
structure = gst_caps_get_structure (caps, 0);
|
|
|
|
if (!structure)
|
|
|
|
goto error;
|
|
|
|
|
|
|
|
if (!width) {
|
|
|
|
} else if (!gst_structure_get_int (structure, "width", &w)) {
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
} else {
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
*width = w;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!height) {
|
|
|
|
} else if (!gst_structure_get_int (structure, "height", &h)) {
|
|
|
|
goto error;
|
|
|
|
} else {
|
|
|
|
*height = h;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!(rate || rate_decimal)) {
|
|
|
|
} else if (!gst_structure_get_fraction (structure, "framerate", &num, &den)) {
|
|
|
|
goto error;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 128) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_1_875;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 64) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_3_75;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 32) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_7_5;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 16) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_15;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 8) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_30;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 4) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_60;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 2) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_120;
|
|
|
|
} else if (gst_util_fraction_compare (num, den, 240, 1) <= 0) {
|
|
|
|
*rate = DC1394_FRAMERATE_240;
|
|
|
|
} else {
|
|
|
|
*rate = DC1394_FRAMERATE_240;
|
|
|
|
}
|
|
|
|
if (rate_decimal) {
|
|
|
|
gst_util_fraction_to_double (num, den, &dec);
|
|
|
|
*rate_decimal = dec;
|
|
|
|
}
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
if (!color_codings) {
|
|
|
|
} else if (gst_structure_has_name (structure, "video/x-raw")) {
|
|
|
|
format = gst_structure_get_string (structure, "format");
|
|
|
|
switch (gst_video_format_from_string (format)) {
|
|
|
|
case GST_VIDEO_FORMAT_GRAY8:
|
|
|
|
color_codings->num = 1;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_MONO8;
|
|
|
|
break;
|
|
|
|
case GST_VIDEO_FORMAT_IYU1:
|
|
|
|
color_codings->num = 1;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_YUV411;
|
|
|
|
break;
|
|
|
|
case GST_VIDEO_FORMAT_UYVY:
|
|
|
|
color_codings->num = 1;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_YUV422;
|
|
|
|
break;
|
|
|
|
case GST_VIDEO_FORMAT_IYU2:
|
|
|
|
color_codings->num = 1;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_YUV444;
|
|
|
|
break;
|
|
|
|
case GST_VIDEO_FORMAT_RGB:
|
|
|
|
color_codings->num = 1;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_RGB8;
|
|
|
|
break;
|
|
|
|
case GST_VIDEO_FORMAT_GRAY16_BE:
|
|
|
|
color_codings->num = 1;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_MONO16;
|
|
|
|
break;
|
|
|
|
/*
|
|
|
|
* The following formats do not exist in Gstreamer:
|
|
|
|
*case GST_VIDEO_FORMAT_RGB48: // Unsigned RGB format 16 bits per channel
|
|
|
|
* color_codings->num = 1
|
|
|
|
* color_codings->codings[0] = DC1394_COLOR_CODING_RGB16;
|
|
|
|
* break;
|
|
|
|
*case GST_VIDEO_FORMAT_GRAY16_BE_SIGNED: // Signed grayscale format 16 bits
|
|
|
|
* color_codings->num = 1
|
|
|
|
* color_codings->codings[0] = DC1394_COLOR_CODING_MONO16S;
|
|
|
|
* break;
|
|
|
|
*case GST_VIDEO_FORMAT_RGB48_SIGNED: // Signed RGB format 16 bits per channel
|
|
|
|
* color_codings->num = 1
|
|
|
|
* color_codings->codings[0] = DC1394_COLOR_CODING_RGB16S;
|
|
|
|
* break;
|
|
|
|
*/
|
|
|
|
default:
|
|
|
|
GST_ERROR ("unsupported raw video format %s", format);
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
} else if (gst_structure_has_name (structure, "video/x-bayer")) {
|
|
|
|
/*
|
|
|
|
* The following formats do not exist in Gstreamer:
|
|
|
|
*switch (gst_bayer_format_from_string(format)) {
|
|
|
|
* case GST_BAYER_FORMAT_BGGR8:
|
|
|
|
* case GST_BAYER_FORMAT_GBRG8:
|
|
|
|
* case GST_BAYER_FORMAT_GRBG8:
|
|
|
|
* case GST_BAYER_FORMAT_BGGR8:
|
|
|
|
* *coding = DC1394_COLOR_CODING_RAW8;
|
|
|
|
* break;
|
|
|
|
* case GST_BAYER_FORMAT_BGGR16_BE:
|
|
|
|
* case GST_BAYER_FORMAT_GBRG16_BE:
|
|
|
|
* case GST_BAYER_FORMAT_GRBG16_BE:
|
|
|
|
* case GST_BAYER_FORMAT_BGGR16_BE:
|
|
|
|
* *coding = DC1394_COLOR_CODING_RAW16;
|
|
|
|
* break;
|
|
|
|
* default:
|
|
|
|
* GST_ERROR("unsupported raw video format %s", format);
|
|
|
|
* goto error;
|
|
|
|
*}
|
|
|
|
*/
|
|
|
|
color_codings->num = 2;
|
|
|
|
color_codings->codings[0] = DC1394_COLOR_CODING_RAW8;
|
|
|
|
color_codings->codings[1] = DC1394_COLOR_CODING_MONO8;
|
|
|
|
} else {
|
|
|
|
goto error;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
return TRUE;
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
|
|
|
|
error:
|
|
|
|
return FALSE;
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
static gboolean
|
|
|
|
plugin_init (GstPlugin * plugin)
|
|
|
|
{
|
|
|
|
GST_DEBUG_CATEGORY_INIT (dc1394_debug, "dc1394", 0, "DC1394 interface");
|
|
|
|
|
|
|
|
return gst_element_register (plugin, "dc1394src", GST_RANK_NONE,
|
2016-06-07 13:50:50 +00:00
|
|
|
GST_TYPE_DC1394_SRC);
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
GST_PLUGIN_DEFINE (GST_VERSION_MAJOR,
|
|
|
|
GST_VERSION_MINOR,
|
2012-04-05 16:02:56 +00:00
|
|
|
dc1394,
|
dc1394src: port to 1.X
The dc1394src is a PushSrc element for IIDC cameras based on libdc1394.
The implementation from the 0.x series is deffective:
caps negotiation does not work, and some video formats
provided by the camera are not supported.
Refactor the code to port it to 1.X and enhance the support
for the full set of video options of IIDC cameras:
- The IIDC specification includes a set of camera video modes
(video format, frame size, and frame rates).
They do not map perfectly to Gstreamer formats, but those that
do not match are very rare (if used at all by any camera).
In addition, although the specification includes a raw format,
some cameras use mono video formats to capture in Bayer format.
Map corresponding video modes to Gstreamer formats in capabilities,
allowing both gray raw and Bayer video formats for mono video modes.
- The specification includes scalable video modes (Format7),
where the frame size and rate can be set to arbitrary values
(within the limits of the camera and the bus transport).
Allow the use of such mode, using the frame size and rate
from the negotiatied caps, and set the camera frame rate
adjusting the packet size as in:
<http://damien.douxchamps.net/ieee1394/libdc1394/faq/#How_do_I_set_the_frame_rate>
The scalable modes also allow for a custom ROI offset.
Support for it can be easily added later using properties.
- Camera operation using libdc1394 is as follows:
1. Enumerate cameras on the system and open the camera
identified the enumeration index or by a GUID (64bit hex code).
2. Query the video formats supported by the camera.
3. Configure the camera for the desired video format.
4. Setup the capture resources for the configured video format
and start the camera transmission.
5. Capture frames from the camera and release them when not used.
6. Stop the camera transmission and clear the capture resources.
7. Close the camera freeing its resources.
Do steps 2 and 3 when getting and setting the caps respectively.
Ideally 4 and 6 would be done when going from PAUSED to PLAYING
and viceversa, but since caps might not be set yet, the video mode
is not properly configured leaving the camera in a broken state.
Hence, setup capture and start transmission in the set caps method,
and consequently clear the capture and stop the transmission
when going from PAUSED to READY (instead of PLAYING to PAUSED).
Symmetrycally, open the camera when going from READY to PAUSED,
allowing to probe the camera caps in the negotiation stage.
Implement that using the `start` and `stop` methods of `GstBaseSrc`,
instead of the `change-state` method of `GstElement`.
Stop the camera before setting new caps and restarting it again
to handle caps reconfiguration while in PLAYING (it has no effect
if the camera is not started).
- Create buffers copying the bytes of the captured frames.
Alternatively, the buffers could just wrap the bytes of the frames,
releasing the frame in the buffer's destroy notify function,
if all buffers were destroyed before going from PLAYING to PAUSED.
- No timestamp nor offset is set when creating buffers.
Timestamping is delegated to the parent class BaseSrc,
setting `gst_base_src_set_live` TRUE, `gst_base_src_set_format`
with GST_FORMAT_TIME and `gst_base_src_set_do_timestamp`.
Captured frames have a timestamp field with the system time
at the completion of the transmission of the frame,
but it is not sure that this comes from a monotonic clock,
and it seems to be left NULL in Windows.
- Use GUID and unit properties to select the camera to operate on.
The camera number used in version 0.X does not uniquely identify
the device (it depends on the set of cameras currently detected).
Since the GUID is 64bit identifier (same as MAC address),
handle it with a string property with its hexadecimal representation.
For practicality, operate on the first camera available if the GUID
is null (default) and match any camera unit number if unit is -1.
Alternatively, the GUID could be handed with an unsigned 64 bit
integer type property, using `0xffffffffffffffff` as default value
to select the first camera available (it is not a valid GUID value).
- Keep name `GstDc1394` and prefix `gst_dc1394` as in version 0.X,
although `GstDC1394Src` and `gst_dc1394_src` are more descriptive.
- Adjust build files to reenable the compilation of the plugin.
Remove dc1394 from the list of unported plugins in configure.ac.
Add the missing flags and libraries to Makefile.
Use `$()` for variable substitution, as many plugins do,
although other plugins use `@@` instead.
https://bugzilla.gnome.org/show_bug.cgi?id=763026
2016-05-10 16:30:35 +00:00
|
|
|
"1394 IIDC video source",
|
Commit new dc1394src element.
Original commit message from CVS:
* configure.ac:
* ext/Makefile.am:
* ext/dc1394/Makefile.am:
* ext/dc1394/gstdc1394.c: (gst_dc1394_base_init),
(gst_dc1394_class_init), (gst_dc1394_init),
(gst_dc1394_src_fixate), (gst_dc1394_set_property),
(gst_dc1394_get_property), (gst_dc1394_getcaps),
(gst_dc1394_setcaps), (gst_dc1394_get_times), (gst_dc1394_create),
(gst_dc1394_parse_caps), (gst_dc1394_change_state),
(gst_dc1394_caps_set_format_vmode_caps),
(gst_dc1394_set_caps_color), (gst_dc1394_set_caps_framesize),
(gst_dc1394_set_caps_framesize_range),
(gst_dc1394_caps_set_framerate_list),
(gst_dc1394_framerate_const_to_frac),
(gst_dc1394_get_all_dc1394_caps), (gst_dc1394_get_cam_caps),
(gst_dc1394_framerate_frac_to_const),
(gst_dc1394_open_cam_with_best_caps),
(gst_dc1394_change_camera_transmission), (plugin_init):
* ext/dc1394/gstdc1394.h:
Commit new dc1394src element.
Patch By: Eric Jonas < jonas at mit dot edu >
Close: #387251
2007-06-29 13:03:27 +00:00
|
|
|
plugin_init, VERSION, GST_LICENSE, GST_PACKAGE_NAME, GST_PACKAGE_ORIGIN)
|