When a pipeline using alsasink and push mode upstream fails
to preroll, the following state will be the case:
- A loop upstream will be PAUSED, pushing a first buffer
- alsasink will be READY, pending PAUSED, because async
On error, the pipeline will switch to NULL. alsasink is in
READY, so goes to NULL immediately. It zeroes its cached
caps. Meanwhile, the upstream loop can cause a caps query,
conccurent with the state change. This will use those cached
caps. If the zeroing happens between the NULL test and the
dereferencing, GStreamer will critical down in the GstValue
code.
Since it appears that such a gap between states (PAUSED
and pushing upstream, and NULL downstream) is expected, we
need to protect the read/write access to the cached caps.
This fixes the critical.
See https://bugzilla.gnome.org/show_bug.cgi?id=731121
This lets oggdemux determine they are not delta units, and removes
spurious per packet warnings about being unable to determine the
packet's keyframeness.
They are very confusing for people, and more often than not
also just not very accurate. Seeing 'last reviewed: 2005' in
your docs is not very confidence-inspiring. Let's just remove
those comments.
This should not cause any actual bug since Theora and Daala have
a maximum shift of 31, and a packet duration of 2^31 seems very
implausible. But it fixes:
Coverity 1139804, 1139803, 1139802
Add an extra function to the oggstream map to inform it about
the incoming buffers. This way oggmux can keep a count on the
vp8 invisible frames and calculate the granulepos correctly.
https://bugzilla.gnome.org/show_bug.cgi?id=722682
vp8 stream header shouldn't be assumed to be provided in caps always
as this would repeat the same code in all demuxers/encoders. Instead,
make oggmux generate them if they are not supplied.
https://bugzilla.gnome.org/show_bug.cgi?id=722682
When seeking back to original state after duration seeks, let
upstream know that we want the whole file, including the last
byte that wasn't requested on the duration seeks.
https://bugzilla.gnome.org/show_bug.cgi?id=724633
video time uses the 'segment' and the text time should use
the 'text_segment'.
If different segments are used for video and text it would
lead to out of sync video/subtitles.
A change in gst_ogg_demux_do_seek caused oggdemux to wait for
a page for each of the streams, including a skeleton stream if
one was present. Since Skeleton only has header pages, that
was never going to end well.
Also, the code was skipping CMML streams when looking for pages,
so would also have broken on CMML streams.
Thus, we change the code to disregard Skeleton streams, as well
as discontinuous streams (such as CMML and Kate). While it may
be desirable to consider Kate streams too (in order to avoid
losing a subtitle starting near the seek point), this may be
a performance drag when seeking where no subtitles are. Maybe
one could add a "give up" threshold for such discontinuous
streams, so we'd get any page if there is one, but do not end
up reading preposterous amounts of data otherwise.
In any case, it is important that the code that determines
the amount of streams to look pages for remains consistent with
the "early out" conditions of the code that actually parses
the incoming pages, lest we never decrease the pending counter
to zero.
This fixes seeking on a file with a skeleton track reading all
the file on each seek.
https://bugzilla.gnome.org/show_bug.cgi?id=719615
Ogg data is read chunk by chunk, and the chunk size used was
originally taken from libvorbisfile. However, this value leads
to poor performance when used on an Ogg file with large pages
(Ogg pages can be close to 64 KB).
We can't just use a larger chunk size, since this will decrease
performance on small page streams, so we use an adaptive scheme
where the chunk size is twice the largest page size we've seen
so far in the stream. For "typical" Ogg/Vorbis, this gives us
almost the same chunk size (a bit lower), and this lets us get
better performance on streams with large pages.
In case we receive a flush event before having our caps set, we will
end up trying to create a theora encoder even though we are not ready.
Avoid that situation making sure we are initialized before accepting to
be flushed.
https://bugzilla.gnome.org/show_bug.cgi?id=709858
The initial support for the new ALSA chmap API.
Just translate the current chmap to GstAudioChannelPosition during the
setup. No function to specify the channel map manually yet, so still
impossible to assign any non-standard positions or to configure in a
different order even if the hardware allows.
https://bugzilla.gnome.org/show_bug.cgi?id=709755
Store the seek stop and seqnum and properly restore them when
receiving the corresponding Segment from upstream. Also fixes
seqnum for converted seek events.
