matroskademux performs segment tricks to skip gaps in streams,
notably at start for non 0 based files. There may however be
cases when full presentation (including intermediate gaps) is
desired, so a property allows to configure as of which gap
to act (or not at all).
API: GstMatroskaDemux::max-gap-time
Fixes#659009.
Subtract the first timestamp of a stream from all input buffers to
get 0-based timestamps for creating a sane ctts table. Without this
patch the ctts could have larger values than needed, causing the
playback to have a delay at startup.
As the first timestamp is only found after a few buffers are queued
(due to possible reordered buffers), once we find the first timestamp
we subtract it from all buffers on the queue, from that point on,
all buffers have their timestamps subtract when they are collected.
https://bugzilla.gnome.org/show_bug.cgi?id=658659
Frame duration might vary for 1 usecond, in this case matroskamux
decides to create BLOCKGROUP instead of SIMPLEBLOCK.
Convert duration to timecodescale which is (typically) less precise, and
then also allow the difference of 1/-1 to arrange for less sensitive check.
Based on patch by Alexey Fisher <bug-track@fisher-privat.net>
Fixes#653080.
Some encoders (Arecont) do not like the long OPTIONS sent at startup as sent by
GStreamer, but do accept the short header as sent by Live555.
This patch makes the extending the request optional by adding a property
(short-header).
Fixes#655805.
API: GstRTSPSrc:short-header
We used to skip frame rate setup if the camera was already setup
with the requested frame rate. This breaks some cameras though,
causing them to not output data (several models of Thinkpad cameras
have this problem at least).
So, don't skip.
https://bugzilla.gnome.org/show_bug.cgi?id=638300
flacdec converts the src timestamp to a sample number, uses that internally, then reconverts the sample number to a timestamp for the output buffer. Unfortunately, sample numbers can't be represented in an integer number of nanoseconds, and the conversion process was truncating rather than rounding, resulting in sample numbers and output timestamps that were often off by a full sample.
This corrects the time->sample convesion
This likely breaks stuff. The good: all of the methods now create
field images aligned with input frames, without timestamp mangling.
The bad: this touches a lot of code, much of which is hairy and in
need of cleanup. However, at this point we can reasonably create a
PSNR-based test.
There's no use in splitting the incoming data down to the segsize
limit - by writing as much as possible in one chunk, we increase
performance and avoid PulseAudio unnecessary rewinds.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
In particular, do so even if failing to read while prerolling,
such as when reading from a partial file (eg, while it is being
downloaded).
This fixes a wedge in playbin2.
https://bugzilla.gnome.org/show_bug.cgi?id=651965
The libFLAC API is callback based, and we must only call it to
output data when we know we have enough input data. For this
reason, a single processing step is done when receiving a buffer.
However, if there were metadata buffers still pending, a step
intended for the first audio frame might end up writing that
leftover metadata. Since a single step is done per buffer, this
will cause every buffer to be written one step late.
This would add some latency (a bufferfull's worth), possibly
lose a buffer when seeking or the like, and also cause timestamp
and offset to be applied to the wrong buffer, as updates to
the "current" segment last_stop (from incoming buffer timestamp)
will be applied to an output buffer originating from the previous
incoming buffer.
This fixes the issue by ensuring that, upon receiving the first
audio frame, processing is done till all metadata is processed,
so the next "single step" done will be for the audio frame. After
this, we should keep to 1 input buffer -> 1 output buffer and so
avoid getting out of sync.
https://bugzilla.gnome.org/show_bug.cgi?id=650960
