In this case the video still goes through the text chain and
subtitles are still going in there, in case subtitles are
enabled again. This makes sure that re-enabling subtitles
happens instantly.
Fixes hanging video when disabling subtitles, caused by an
unliked video pad.
This is necessary because the sinks don't notice the group switches
and the decoders/demuxers have a different running time than the
sinks.
Fixes bug #537050.
In some cases (all buffers dropped by a parser) a decodebin2
chain might receive an EOS before it gets enough data to
expose a decoded pad. In the case that no streams can expose
a pad we should error out instead of hang.
Fixes#542758
Just counting how many messages were sent and how many were received
is not good enough because they might've been duplicated (e.g. by the
visualization audio tee). Comparing the sequence numbers should give
better results in that case.
Otherwise the async state change from READY->PAUSED of the
uridecodebins will take playbin2 from PLAYING->PAUSED again
during gapless group switches.
Fixes bug #602000.
When a decodebin2 receives no-more-pads of a group it
can set that group's multiqueue buffering thresholds to
'playing' buffering method, avoiding that it buffers
too long and cause problems when using with queue2.
See the associated bug for details.
Fixes#600787
During a group switch return the cached duration of the old group
because the old group still didn't finish playback. If we have no
cached duration return FALSE.
Fixes bug #585969.
Make sure, to only "simulate" subtitle no-more-pads if it was still
pending and also handle errors in the subtitle pipeline as warnings
after the subtitles prerolled.
Don't set the suburidecodebin to READY after errors, handle_message
will usually be called from the streaming thread and doing that
from there is obviously not a good idea.
Now the caps property isn't set anymore for the subtitle caps
but instead in the autoplug-continue signal it is detected
if the caps belong to a supported subtitle stream.
This makes automatic use of newly installed plugins.
First of all, make sure that suburidecodebin never
errors out because of not-linked in case external subtitles
are used but then subtitles are disabled.
And then make sure that external subtitles always start from
the correct position and are not racing until EOS if they
get unselected and selected again.
This will make sure that no subparse is ever plugged and subtitleoverlay,
that subpicture streams are handled the same was as subtitles and that
subtitle renderers are used if available.
Fixes bugs #595123, #570753, #591662, #591706.
Using the object lock here can and will lead to deadlocks because
of deep-notifies of property changes: the deep-notify handler will
get the parent of objects, which will take the object lock again.
Fixes bug #600479.
Use the faster gst_element_link_pads because we know for sure the sinkpad name
and we don't need to have the function search for a suitable pad anymore.
We want to return NOT_LINKED for unselected pads but only for pads
from the normal uridecodebin. This makes sure that subtitle streams
are not raced past audio/video from decodebin2's multiqueue.
For pads from suburidecodebin OK should always be returned, otherwise
it will most likely stop with an error.
There's not much point in using GST_DEBUG_FUNCPTR with GObject
virtual functions such as get_property, set_propery, finalize and
dispose, since they'll never be used by anyone anyway. Saves a
few bytes and possibly a sixteenth of a polar bear.
Set the output caps on the srcpad before pushing the buffer because else core
will do a rather expensive check to see if we can actually accept those caps on
the srcpad.
Install a custom acceptcaps function instead of using the default expensive
check. We accept whatever downstream accepts so we pass along the acceptcaps
call to the downstream peer.
I also renamed glib_enum_prefix to glib_gen_prefix as we also use that for the
marshallers. Also rename the rtsp-marshal.list to work with the unified prefix.
instead of printing an error that no corresponding group could
be found. no-more-pads from non-demuxer elements doesn't give
any additional information because there can only be a single srcpad.
Fixes bug #598288.
This allows partial group changes, i.e. demuxer2 in the example below
goes EOS but has a next group and audio2 stays the same.
/-- >demuxer2---->video
demuxer--- \--->audio1
\--->audio2
This now keeps track of everything that is going on, creates
a tree of chains and groups to allow "demuxer after demuxer" scenarios
and allows chained Oggs with multiple streams (needs oggdemux or playbin2 fixes).
Also document everything in detail and give a general overview of what
decodebin2 is doing at the top of the sources.
Fixes bug #596183, #563828 and #591677.
Pad blocks should never be done on external pads as outside elements
might want to use their own pad blocks on them and this will lead to
conflicts and deadlocks.
This allows using playsink from outside the playback plugin.
Add code to be able to request the sink pads using standard GStreamer API.
TODO : expose GObject properties/signals.
g_value_set_object() increases the refcount of the sink, which is not needed
because the object should already be refcounted. Make sure this is always the
case and use g_value_take_object().
Fixes: #592884
Before, SEEK events would be sent to the video sink, which wouldn't
be linked in any way to the subtitle part of the pipeline and
subparse would never see the SEEK event. This would then seek
the audio/video but the subtitles would continue from the old
position instead.
Fixes bug #591664.
The problem with an error message is, that it will stop playback completely
while it could be that only a audio decoder plugin is missing and the video
could be played with the available plugins.
See bug #591677.
Before we had STREAM/WRONG_TYPE but it's really CORE/MISSING_PLUGIN
because a plugin is missing and nothing else is wrong.
Also make it an error instead of a warning.
Really fixes bug #591677.
Don't do fallbacks if application specified a sink element. When doing the
fallback use configured default elements instead of hardcoded linux only
elements. Improve error messages accordingly.
If a downstream element returns an error while upstream has already
put all data into queue2 (including EOS), upstream will no longer
chain into queue2, so it is up to queue2 to perform some
EOS handling / message posting in such cases. See #589991.
Rename the GType of the pads of playbin's internal stream selector
element so they don't use the same type name as input-selector's
pads. Fixes#589622.
Keep track of the max requested position and compare this to the write position
in the temp file to get the current amount of buffered data.
Fix memleak of all incomming buffers.
Fixes#588551
We shouldn't really depend on elements from -bad for stream
selection in playbin2, so use a private copy of input-selector
until the selector plugin is ready to be moved to -base or -good.
Fixes#586356.
Don't flush the file by closing and opening it but instead use g_freopen. This
avoids a deadlock in shutdown because we emit the temp-location property change
with the wrong lock held.
Fix the construction of the temporary filename construction as the application
name can be NULL and we don't want a separator between the prgname and the
template.
Add a download property that will attempt to configure queue2 into progressive
download buffering.
Make sure we only enable download buffering for quicktime and flv formats.
Add a new temp-template property so that queue2 can securely allocate a
temporary filename. Deprecate the temp-location property for setting the
location but still use it to notify the allocated temp file.
If READY->PAUSED failed in the source element we would've swapped
the current and next group already. To allow READY->PAUSED to succeed
after the first failure we have to swap the current and next group
back again. This also ensure that we're again in the same state
as before the failed state change and not at the next group.
This was especially a problem for playbin2 pipelines that use the
new mounting support in giosrc as the source would fail for READY->PAUSED
the first time, the application mounts the location and then tries
to go READY->PAUSED again (and this time it would succeed).
Fixes bug #588078.
Set the target state of the newly added uridecodebins to somthing else that
PAUSED so that we keep their state in sync with the playsink state.
Fixes#585268
uridecodebin expects the passed connection-speed value in kbps, so we
need to divide the value stored in bps by 1000. Also, lower the upper
limit on the properties to the value that we can actually store in our
internal guint (which is plenty high enough)
When we are probing for streams, we want to set the queue size in such a way
that we can scan a maximum amount of data without consuming too much memory.
Therefore, remove the time limit on the queue and only stop scanning after 2MB
of data.
See #584104.
Recognise PGS subpicture streams and connect them to the SPU pad
in playsink. Unfortunately this fails badly with negotiation errors
if the SPU is not recent enough to support the stream. I'm not sure
how to add format negotiation in yet.
When using an audio sink without a "volume" property, volume control
would only work for the first song. For the next song, we'd try to
re-use the existing audio chain, but inadvertently set chain->volume
to NULL instead of to the existing volume element.
playbin2 inadvertently used autoaudiosink and autovideosink up to now,
since it would overwrite the sinks configured via the "audio-sink"
and "video-sink" properties with the stream-specific group sinks when
configuring the outputs. Those are usually NULL however, so that would
overwrite the configured sinks with NULL which makes playbin2 then
default to the auto sinks. Fix this by keeping a reference to each
configured sink in playbin2 and setting up the right sinks depending
on whether there is a stream-specific sink or not.
Fixes#584020.
Use two flags to remember volume/mute changes at times when we don't have the
audiochain yet (e.g. construction). Only set values when they were actualy
changed. This makes pulseaudio's stream restore functional.
Add a queue2 after the raw output pads of certain sources such as those for uris
like cdda://
No tuning of the queue is done yet as the defaults seem to work fine for me.
Fixes#582528
Keep track of the autoplugged custom sinks and configure them in the playsink
element when we have collected all streams.
Also make sure that we only select one custom sink.
When unreffing the internal sink, we don't need to change the state to NULL.
Make playsink go async to the PAUSED state instead of relying on uridecodebin
for async behaviour in playbin. This solves some problems (mainly with DVD)
where the pipeline would go to PLAYING before preroll completed, failing to
select the audiosink clock.
Fixes#581727
The 2s limit is way too small for a lot of files (which have an interleave
in time of between 3 and 5s). Instead, leave it to the initial 5s value
and reduce the other limits (allowing us to stay memory-efficient).
First check the pad caps if they are raw before setting the raw_decoding_mode to
TRUE. Fixes playback of transport streams and other streams that require large
queues.
Fixes#579734
Clear the target of our ghostpads before we remove the pad from the element.
This to make sure that the internal pad is not left linked to whatever pad we
were ghosted to. This should only be a problem when we leak the ghostpads.
Also release our subpicture pads.
Fixes#577288.
Raw decoding mode removes almost all buffering in video and audio queues
when a source providing already decoded video/audio is detected, on the
possibly bogus assumption that such a source should provide sufficient
internal queueing. Fixes playback on some DVDs, and improves it
on all.
When reusing playbin with visualisations, reset the async property on the video
sink because some sinks might dynamically recreate their sinks.
Fixes#576188
When we have the textpad configured, enable and disable the subtitles by setting
the silent flag on the overlay element instead of trying to remove elements.
See #576187
Link after doing the state change and unlink before shutting down. Makes the
window for causing races in toggling the visualisations smaller.
See #576187.
Remove the group GCond that we used for waiting for groups to finish because we
use pad blocking on the selectors and counters instead for waiting for the
groups to complete.
remove the obsolete about_to_finish variable set while emiting the
about-to-finish signal and fix some old comments.
We don't need to take the playbin lock when querying the uridecodebin.
When we make a group connected to a demuxer, keep an extra dynamic refcount for
the group which is only decremented when no_more_pads or a multiqueue overrun is
detected. This way we avoid a race between exposing the group while more dynamic
refs are added from new pads.
Fixes#575588.
Sync the state of the newly added chains to the state of the parent sink element
to avoid lost async-start messages. Fixes cdda:// async-done message storm.
When streams are not selected in the selector, return NOT_LINKED so that
upstream elements can skip decoding. Only do this for audio and video pads
because for text streams the overhead is smaller and they could come from
external files.
Set the custom sink async=FALSE to not make it participate in preroll because we
are dealing with sparse streams.
Try to set sync=TRUE on the custom text sink.
Release the shutdown lock when we wait for other groups to complete or else we
have a deadlock when the other group completes and tries to grab the shutdown
lock.
Fixes#575550.
Add property to playbin2 to configure a custom sink that receives the raw
subtitle buffers instead of using a textoverlay.
Improve the property finding code to make it more usable.
Use property find code to find async properties in custom sinks that are bins.
Improve text overlay code to gracefully handle missing elements.
Disconnect the notify::caps signal in our callback (it'll be re-added
if we're not, in fact, finished getting complete caps). Ensures that
caps changes mid-stream (e.g. from an mp3 that changes from
stereo->mono mid-file) don't cause us to try to add a new pad.
Make it possible to request a flushing pad from the playsink. We can eventually
use these flushing pads to quickly terminate the dataflow when we are shutting
down.
Release the group lock while we perform the state changes on the uridecodebins
because that might trigger callbacks that we need to handle with the group lock
taken. Avoids a possible deadly embrace in some id3/flac files.
Fixes#567396.
Rather than only checking for volume property on the audio sink
directly, recursively look for it on sinks within it (if it's a bin).
Allows use of sink-as-volume-control where the application has supplied
an audio-sink bin that includes a real audio sink internally.
Don't keep extra references to volume and mute elements; we don't need
to do so.
Ensure we unref pads that we have references to, and release request
pads.
We can use gst_element_link_pads() instead of the more generic
gst_element_link() function because we know the pads. This saves some cycles
because the more generic function needs to search for possible compatible caps
etc.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (gst_play_bin_class_init),
(gst_play_bin_set_uri), (gst_play_bin_set_suburi),
(no_more_pads_cb), (drained_cb), (group_set_locked_state_unlocked),
(activate_group), (deactivate_group), (groups_set_locked_state),
(gst_play_bin_change_state):
Fix some comments and docs.
Post an error message when we fail to link the selector to the sink.
Remove pushing of EOS, this seems unneeded.
Lock the state of deactivated groups so that they don't accidentally
reactivate when the playbin2 state changes.
Reuse uridecodebins.
Unlock and relock state of groups when playbin goes to NULL.
Fixes#566654.
Fixes#566341.
* gst/playback/gsturidecodebin.c: (pad_removed_cb), (type_found):
Only do something in the pad removed callback when we are dealing with
our sourcepads because the sinkpads don't have a ghostpad.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (notify_source_cb), (activate_group):
Disconnect signal handlers before destroying a previous decodebin so
that we don't end up causing deadlocks. Fixes#566586.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (no_more_pads_cb):
Add some debug info.
* gst/playback/gstplaysink.c: (gen_video_chain), (gen_audio_chain),
(gst_play_sink_reconfigure), (gst_play_sink_request_pad),
(gst_play_sink_release_pad):
Add some more debug info.
Reconfigure the audio chain when we switch between raw and encoded audio
in gapless playback.
Original commit message from CVS:
* gst/playback/gsturidecodebin.c: (gst_uri_decode_bin_finalize):
Free the factory array when finalizing.
* sys/v4l/gstv4lsrc.c: (gst_v4lsrc_base_init):
Use a GstStaticPadTemplate since the src pad caps are fixed.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (gen_audio_chain),
(gst_play_sink_reconfigure):
Add some more debug info.
Fix linking of just an encoded sink.
Handle failure to create a sink chain more gracefully than crashing.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (pad_added_cb):
Error out with a missing-plugin error when the input-selector was not
found.
* gst/playback/gstplaysink.c: (gst_play_sink_reconfigure):
Indentation.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (gst_play_sink_class_init),
(gst_play_sink_dispose), (gst_play_sink_finalize), (try_element),
(gen_video_chain), (gen_audio_chain), (gst_play_sink_reconfigure),
(gst_play_sink_send_event), (gst_play_sink_change_state):
Use G_DEFINE_TYPE.
Try to set the selected sink to READY before using it. This will allow
for detection of incompatible formats sooner.
Don't cause a fatal error when conversion elements are missing but post
a missing-element message and a warning instead because things might
still link and run fine.
Simplyfy the construction of audio and video sink chains.
Original commit message from CVS:
* gst/playback/gstdecodebin.c:
* gst/playback/gstdecodebin2.c:
Add basic docs to decodebin and link to decodebin from decodebin2.
Original commit message from CVS:
* gst/playback/gstplaybin2.c:
Add notification of current stream. Add ability to configure buffer
sizes.
* gst/playback/gsturidecodebin.c:
Add ability to configure buffer sizes for streaming mode.
Bug #561734.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (gen_audio_chain):
Don't post an error when we can't configure the volume but post a
warning instead. Fixes#561780.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c:
If the top-level type of the stream is plain text, don't try to decode
it, matching behaviour of decodebin.
* gst/playback/gstplaysink.c:
If we fail to generate a text chain (e.g. due to missing optional
plugins), don't crash.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (deactivate_group):
don't try to unlink the selector sinkpad when we don't have it yet. This
can happen if an error occured before the group was complete.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (activate_group):
Catch state change errors and stop from the uridecodebin elements
instead of trying to continue in vain.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (gst_play_sink_reconfigure):
Don't try to do crazy things when we only have a text pad without a
video pad. Fixes#559478.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_pad_activate):
Remove bogus assert, the decodepad could have been created inside an
already existing group.
Original commit message from CVS:
2008-10-08 Andy Wingo <wingo@pobox.com>
* gst/playback/gstdecodebin2.c (expose_pad): Fix typo: unset
target instead of setting it.
(gst_decode_pad_activate, gst_decode_pad_unblock): This is now the
API for a decode pad. The bugfix is that we set the group in
activate(), not when the pad was created because it might be NULL
then.
(gst_decode_group_control_source_pad, gst_decode_group_expose):
Update to use the API.
Original commit message from CVS:
2008-10-08 Andy Wingo <wingo@pobox.com>
* gst/playback/gstdecodebin2.c (struct _GstDecodePad): Change to
be a subclass of GstGhostPad.
(analyze_new_pad): So, when emitting the signals that determine
how we do autoplugging, already create the ghost pad and use it as
the pad in the signal arguments. This allows applications to make
a connection between the pad passed in e.g. autoplug-continue, and
the pad passed in new-decoded-pad.
(connect_pad, expose_pad): Update to receive the ghosted decode
pad in the args, retargetting it as necessary if we have to plug
the target pad through a multiqueue.
(gst_decode_group_control_source_pad): Adapt to receive an
already-ghosted pad that just needs activation, blocking, and
drain notification.
(sort_end_pads): Adapt for decode pads actually being pads.
(gst_decode_group_expose): Adapt for decode pads actually being
pads. Rewrite the decode pad names so they appear in order. Adds a
new error case if we couldn't set the name.
(gst_decode_group_free, gst_decode_group_hide): Adapt cleanup
logic.
(gst_decode_pad_set_blocked, gst_decode_pad_add_drained_check):
New API for the decode pad, needed because we shouldn't do these
things inside gst_decode_pad_new(), but after.
(gst_decode_pad_new): Change to actually make the real pad, and
delay the blocking/drainage bits.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (selector_blocked), (pad_added_cb),
(no_more_pads_cb):
Fix nasty race where multiple decodebins could start pushing data before
we manage to configure the sinks, resulting in not-linked errors in
typical RTSP streaming cases.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c:
Fix property doc markup (its not a signal).
* sys/xvimage/xvimagesink.c:
Add since tag for new proeprties (also add sice tags fro the last two
other additions).
Original commit message from CVS:
* gst/playback/gstplaybasebin.c:
* gst/playback/gstplaybasebin.h:
* gst/playback/gstplaybin.c:
* gst/playback/gststreamselector.c:
First stab at integrating DVD subpicture overlay into
playbin. Successfully plugs and plays, but the queues need
shrinking - 3 seconds of video is too much buffering.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (add_raw_queue):
And ref the pad before returning it again when linking to the queue
failed. Otherwise we will unref the pad twice later and things break.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (add_raw_queue):
If linking the raw pad with a queue fails, try it without a queue
instead of failing completely. This should never happen.
Original commit message from CVS:
Patch by: Evgeniy Stepanov <eugeni dot stepanov at gmail dot com>
* gst/playback/gstdecodebin.c: (add_raw_queue), (close_pad_link):
Add a queue after a demuxer if the demuxer outputs raw data. This was
done before only for non-raw data but is required in this case too.
Fixes bug #540215.
decodebin2 doesn't have this issue because all streams of a group
go through multiqueue.
Original commit message from CVS:
* gst/playback/gstplay-marshal.list:
* gst/playback/gstplaybin2.c:
Add get-video-pad, get-audio-pad, get-text-pad action signals to
playbin2. This allows the user to get to the selector's sinkpads, and
thus inspect a range of things - caps, tags, etc.
Original commit message from CVS:
* gst/playback/gstplaybin2.c:
* gst/playback/gstplaysink.c:
Fix a whole bunch of typos in comments and log statements.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c:
Ensure decodebin2 emits 'drained' signal once, and only once, when all
pads are drained.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (gst_play_bin_get_property),
(notify_source), (activate_group):
Implement the source property, emit notify when it changes in the
underlying uridecodebin.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c:
Disconnect signals from decodebins we created before we remove it from
playbin, to avoid crashes if the decodebin is eventually disposed after
the playbin itself (possible if the app takes a reference on the
decodebin).
Fixes#536521.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c:
(gst_decode_group_control_source_pad), (gst_decode_group_expose):
Check for NULL cases and log them, creating ghostpads can, for example,
fail when the pad returns wrong caps.
* gst/playback/gstplaybin2.c: (perform_eos):
When pushing out the EOS event, collect the return value and warn when
something failed.
Original commit message from CVS:
Patch by: Sjoerd Simons <sjoerd at luon dot net>
* gst/playback/gstdecodebin.c: (remove_fakesink):
Lock the fakesink before setting the state to NULL and removing it from
the bin so that a concurrent state change cannot interfere.
Fixes#534331.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_class_init):
* gst/playback/gstdecodebin2.c: (gst_decode_bin_class_init):
* gst/playback/gstplay-marshal.list:
* gst/playback/gsturidecodebin.c: (gst_uri_decode_bin_class_init):
Use correct marshallers. GstCaps are a boxed type and no GObject
subclass.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (connect_pad):
When autoplugging fails, set the element back to NULL before
unreffing it.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (set_audio_mute),
(set_active_source):
* gst/playback/gstplaybasebin.h:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init),
(playbin_set_audio_mute):
Allow setting -1 as current-audio to mute the current audio stream,
similar to what is done for subtitles. Fixes bug #342294.
Original commit message from CVS:
* gst/playback/test4.c:
* gst/playback/test5.c:
* gst/playback/test6.c:
* gst/playback/test7.c:
Also include config.h when relying on defines from it. Fixes the
build. Its been a please to serve :)
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (free_pad_probe_for_element),
(try_to_link_1):
If we can't activate one of the decoders we plugged in (such as,
say, musepackdec) for some reason (it might not support push mode,
for example), remove any pad probes that close_pad_link() might
have set up. This makes sure we later don't try to remove a probe
for a pad that doesn't exist any longer, and avoids nast warnings
and probably other things too.
Original commit message from CVS:
* gst/playback/test4.c:
* gst/playback/test5.c:
* gst/playback/test6.c:
* gst/tcp/gstmultifdsink.c:
Include stdlib.h and unistd.h only if the appropriate HAVE_*_H macro
is defined.
Original commit message from CVS:
* docs/design/draft-keyframe-force.txt:
Fix typo.
* gst/playback/gstqueue2.c: (update_buffering),
(gst_queue_handle_src_query):
Set buffering mode in the messages.
Set buffering percent in the query.
* tests/examples/seek/seek.c: (update_fill), (msg_state_changed),
(do_stream_buffering), (do_download_buffering), (msg_buffering):
Do some more fancy things based on the buffering method in use.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (update_buffering),
(gst_queue_close_temp_location_file), (gst_queue_handle_src_query),
(gst_queue_src_checkgetrange_function):
Include extra buffering stats in the buffering message.
Implement BUFFERING query.
* gst/playback/gsturidecodebin.c: (do_async_start),
(do_async_done), (type_found), (setup_streaming), (setup_source),
(gst_uri_decode_bin_change_state):
Only add decodebin2 when the type is found in streaming mode.
Make uridecodebin async to PAUSED even when we don't have decodebin2
added yet.
Original commit message from CVS:
* gst-libs/gst/audio/gstbaseaudiosink.c:
(gst_base_audio_sink_class_init):
* gst-libs/gst/audio/gstbaseaudiosrc.c:
(gst_base_audio_src_class_init):
* gst/playback/gstplayback.c: (plugin_init):
* gst/volume/gstvolume.c: (plugin_init):
Work around missing bits of thread-safety on older GLibs some
more to avoid assertions when starting up multiple playbin
objects concurrently (see #512382).
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_class_init),
(gst_decode_bin_init), (gst_decode_bin_dispose),
(gst_decode_bin_set_sink_caps), (gst_decode_bin_get_sink_caps),
(gst_decode_bin_set_property), (gst_decode_bin_get_property),
(analyze_new_pad), (connect_pad), (expose_pad),
(gst_decode_group_new), (gst_decode_group_control_demuxer_pad),
(gst_decode_group_expose), (gst_decode_group_free),
(do_async_start), (do_async_done), (gst_decode_bin_change_state):
Remove fakesink hack, we can now implement this more elegantly.
Added property to bypass typefinding.
Removed underrun callback and demuxer pad probe, we now use the srcpad
probe to expose groups.
API::sink-caps property
* gst/playback/gstplaybin2.c: (no_more_pads_cb):
Guard against multiple emissions of the no_more_pads signal, which
happens when we are dealing with chained oggs.
* gst/playback/gsturidecodebin.c: (remove_decoders),
(make_decoder), (type_found), (setup_streaming), (source_new_pad),
(setup_source):
For streams, use our own typefind element and plug our queue after it.
We will need this to determine the type of buffering to use for the
queue soon.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (update_out_rates),
(gst_queue_open_temp_location_file),
(gst_queue_close_temp_location_file), (gst_queue_handle_src_event),
(gst_queue_handle_src_query), (gst_queue_set_property):
Update the estimated input data when we push out a buffer.
Add some debug info about the temp file.
Only forward src events when we are not using a temp file.
Don't block the duration query, we need to find something better.
Don't leak the temp filename.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (gst_queue_is_filled):
The queue is never filled when there are no buffers in the queue at all.
Fixes#523993.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (gst_play_bin_class_init),
(init_group), (free_group), (gst_play_bin_init),
(gst_play_bin_finalize), (gst_play_bin_set_uri),
(gst_play_bin_set_suburi), (gst_play_bin_get_video_tags),
(gst_play_bin_get_audio_tags), (gst_play_bin_get_text_tags),
(gst_play_bin_set_current_video_stream),
(gst_play_bin_set_current_audio_stream),
(gst_play_bin_set_current_text_stream),
(gst_play_bin_set_encoding), (gst_play_bin_set_property),
(gst_play_bin_get_property), (pad_added_cb), (pad_removed_cb),
(no_more_pads_cb), (perform_eos), (autoplug_select_cb),
(activate_group), (deactivate_group), (setup_next_source),
(save_current_group), (gst_play_bin_change_state):
Update some docs.
Add new locks and conds to protect pipeline creation and group
switching.
Implement the sub-uri property.
Keep track of pending uridecodebin creation and configure the output
pipeline after all streams are configured.
Propagate subtitle encoding to the uridecodebins.
Implement getting the video/audio/visualisation elements.
Use input-selector for stream switching.
If we are asked to do visualisation, prefer to autoplug raw sinks
instead of sinks that accept encoded data.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (gst_play_sink_class_init),
(gst_play_sink_init), (gst_play_sink_dispose),
(gst_play_sink_set_video_sink), (gst_play_sink_get_video_sink),
(gst_play_sink_set_audio_sink), (gst_play_sink_get_audio_sink),
(gst_play_sink_vis_unblocked), (gst_play_sink_vis_blocked),
(gst_play_sink_set_vis_plugin), (gst_play_sink_get_vis_plugin),
(gst_play_sink_set_volume), (gst_play_sink_get_volume),
(gst_play_sink_set_mute), (gen_video_chain), (gen_text_chain),
(gen_audio_chain), (gen_vis_chain), (gst_play_sink_reconfigure),
(gst_play_sink_set_font_desc), (gst_play_sink_get_font_desc),
(gst_play_sink_send_event_to_sink), (gst_play_sink_change_state):
* gst/playback/gstplaysink.h:
Add methods to get audio/video/vis elements.
Add methods to set the font description for the overlay.
Remove properties, we're using this element with its methods only.
Add support for subtitles.
Rearrange the locking a bit to not use the object lock for protecting
the pipeline construction.
Try to use the volume and mute property on the sink when its available.
Implement the mute option with volume when the sink does not have a mute
property.
Only add volume element when the sink has no volume property.
Only do visualisations with raw audio pads.
Original commit message from CVS:
* gst/playback/gsturidecodebin.c:
(gst_uri_decode_bin_autoplug_factories),
(gst_uri_decode_bin_class_init), (gst_uri_decode_bin_init),
(gst_uri_decode_bin_finalize), (gst_uri_decode_bin_set_encoding),
(gst_uri_decode_bin_set_property),
(gst_uri_decode_bin_get_property), (no_more_pads_full),
(new_decoded_pad_cb), (gen_source_element), (remove_decoders),
(proxy_autoplug_factories_signal), (make_decoder),
(source_new_pad), (setup_source):
Add a readonly source property and notify.
Add new lock for protecting the construction of the pipeline.
Keep track of the decodebins we plugged.
Correctly proxy the autoplug signal so that it actually continues.
Proxy subtitle-encoding to the decodebins.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_dispose),
(gst_decode_bin_set_caps), (gst_decode_bin_get_caps),
(gst_decode_bin_set_subs_encoding),
(gst_decode_bin_get_subs_encoding),
(gst_decode_bin_autoplug_factories), (connect_pad), (are_raw_caps),
(deactivate_free_recursive):
Protect caps property with the object lock.
Protect encoding property with the object lock.
Keep list of elements we added that have the subtitle-encoding property.
Distribute the subtitle-encoding to all of the elements when it
changes.
Original commit message from CVS:
* gst/playback/gststreamselector.c: (gst_selector_pad_event),
(gst_selector_pad_chain):
* gst/playback/gststreamselector.h:
Revert change that caused regression until a real fix is found.
Fixes#522203.
Original commit message from CVS:
Patch by: José Alburquerque <jaalburqu svn gnome org>
* gst/playback/gstplaybin2.c:
Make the function signature of the _get_*_tags() functions match
the signature of the vfuncs they implement, ie. return a
GstTagList rather than a GstStructure, which is more correct,
even if one is typedef'ed to the other (#518940).
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (gst_play_bin_set_property):
Enable vis setting.
* gst/playback/gstplaysink.c: (gst_play_sink_init),
(gst_play_sink_dispose), (gst_play_sink_vis_unblocked),
(gst_play_sink_vis_blocked), (gst_play_sink_set_vis_plugin),
(gen_vis_chain):
Implement vis switching while playing.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (find_property),
(gst_play_sink_find_property), (gen_video_chain),
(gst_play_sink_reconfigure), (gst_play_sink_get_last_frame):
Recursively search the sink element for a last-frame property so that we
can also find the property in autovideosink and friends that don't
always proxy the internal sink properties.
Original commit message from CVS:
* gst/playback/gstscreenshot.c:
* gst/playback/gstscreenshot.h:
Fix up copyright (I rewrote the GStreamer-0.10 code for
this from scratch back in the days).
Original commit message from CVS:
* gst/playback/Makefile.am:
* gst/playback/gstscreenshot.c: (feed_fakesrc), (save_result),
(create_element), (gst_play_frame_conv_convert):
* gst/playback/gstscreenshot.h:
Add screenshot conversion code from totem.
* gst/playback/gstplay-marshal.list:
* gst/playback/gstplaybin2.c: (gst_play_marshal_BUFFER__BOXED),
(gst_play_bin_class_init), (gst_play_bin_convert_frame),
(gst_play_bin_get_property), (no_more_pads_cb), (activate_group):
Implement frame property to get a color-unconverted snapshot.
Implement convert-frame action signal to get a converted snapshot image.
Configure connection speed in uridecodebin.
Document some more properties.
* gst/playback/gstplaysink.c: (gst_play_sink_class_init),
(gen_video_chain), (gen_audio_chain), (gst_play_sink_reconfigure),
(gst_play_sink_get_last_frame):
* gst/playback/gstplaysink.h:
Use last-buffer property of the video sink to get a video snapshot.
* tests/examples/seek/seek.c: (shot_cb), (main):
Add snapshot button for playbin2 and use the frame property to save the
frame as a png in the current directory.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (pad_added_cb), (pad_removed_cb),
(no_more_pads_cb):
Get the object data correct so that we can remove our channels
correctly.
* gst/playback/gstplaysink.c: (gen_video_chain), (gen_audio_chain),
(gen_vis_chain), (gst_play_sink_reconfigure),
(gst_play_sink_request_pad):
Add option to disable async behaviour in the sinks when possible. This
makes it possible to avoid an audio queue when dealing with
visualisations.
Add option to add a queue for the audio path.
* tests/examples/seek/seek.c: (clear_streams), (update_streams),
(main):
Disable the vis checkbox to match the defaults of playbin2.
Only get the stream info when we need to.
Original commit message from CVS:
* gst/playback/gstplaysink.c: (gst_play_sink_set_mute),
(gst_play_sink_get_mute), (gen_video_chain), (gen_audio_chain),
(gen_vis_chain), (gst_play_sink_reconfigure),
(gst_play_sink_request_pad):
Move tee in front of the audio and vis pipelines.
Add queue for audio for now.
Add visualisation support.
* tests/examples/seek/seek.c: (main):
Visualisation is by default disabled.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_audio_element):
* gst/playback/gstplaysink.c: (gen_audio_chain):
Handle case where we can't create the volume element a bit
better (#514307).
Original commit message from CVS:
* gst/playback/gstplaybasebin.c:
Set is_dynamic as True if there are elements with both request
and sometimes src pad templates instead of breaking out when it
finds the first pad template that is a src.
Original commit message from CVS:
* gst/playback/gstplay-marshal.list:
Added marshal for streamselector Tags.
* gst/playback/gstplaybasebin.c: (set_active_source):
Streamselector now selects pads based on the pad object instead of its
name.
* gst/playback/gstplaybin2.c: (gst_play_bin_class_init),
(init_group), (gst_play_bin_init), (get_group), (get_tags),
(gst_play_bin_get_video_tags), (gst_play_bin_get_audio_tags),
(gst_play_bin_get_text_tags),
(gst_play_bin_set_current_video_stream),
(gst_play_bin_set_current_audio_stream),
(gst_play_bin_set_current_text_stream),
(gst_play_bin_set_property), (gst_play_bin_get_property),
(pad_added_cb), (pad_removed_cb), (autoplug_select_cb):
Remove option to mute streams with the current-a/v/t property, we have
this functionality in the flags.
Add signals to notify when the number of A/V/T channels changed.
Add action signals to get tags for the A/V/T streams.
Implement setting the current A/V/T stream.
Rearrange some things to simplify stream selection.
Implement volume.
* gst/playback/gstplaysink.c: (gst_play_sink_set_volume),
(gst_play_sink_get_volume), (gst_play_sink_set_property),
(gst_play_sink_get_property), (gen_video_chain), (gen_audio_chain),
(activate_vis), (gst_play_sink_reconfigure):
* gst/playback/gstplaysink.h:
Add and implement volume setting methods.
* gst/playback/gststreamselector.c: (gst_selector_pad_class_init),
(gst_selector_pad_finalize), (gst_selector_pad_get_property),
(gst_selector_pad_event), (gst_stream_selector_class_init),
(gst_stream_selector_init), (gst_stream_selector_finalize),
(gst_stream_selector_set_property),
(gst_stream_selector_get_property),
(gst_stream_selector_get_linked_pad),
(gst_stream_selector_request_new_pad):
* gst/playback/gststreamselector.h:
Add pad properties for tags and status of pads.
Keep tags on pads.
Make active pad selection based on pad object instead of name.
Original commit message from CVS:
* gst/playback/gstplaybin2.c: (gst_play_bin_class_init),
(get_group), (get_n_pads), (gst_play_bin_get_property),
(pad_added_cb), (no_more_pads_cb), (perform_eos),
(autoplug_select_cb), (deactivate_group):
Remove stream-info, we going for something easier.
Refactor getting the current group.
Implement getting the number of audio/video/text streams.
* gst/playback/gststreamselector.c:
(gst_stream_selector_class_init), (gst_stream_selector_init),
(gst_stream_selector_get_property),
(gst_stream_selector_request_new_pad),
(gst_stream_selector_release_pad):
* gst/playback/gststreamselector.h:
Add property for number of pads.
* tests/examples/seek/seek.c: (set_scale), (update_flag),
(vis_toggle_cb), (audio_toggle_cb), (video_toggle_cb),
(text_toggle_cb), (update_streams), (msg_async_done),
(msg_state_changed), (main):
Block slider callback when updating the slider position.
Add gui elements for controlling playbin2.
Add callback for async_done that updates position/duration.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (try_to_link_1):
Make sure we error out correctly if we can't activate one of
the elements we've added. Fixes#508138.
Original commit message from CVS:
* gst/playback/gstplay-enum.c:
(register_gst_autoplug_select_result),
(gst_autoplug_select_result_get_type), (register_gst_play_flags),
(gst_play_flags_get_type):
* gst/playback/gstplay-enum.h:
Add enums for configuration flags.
* gst/playback/gstplaybin2.c: (gst_play_bin_class_init),
(init_group), (gst_play_bin_init), (gst_play_bin_set_property),
(gst_play_bin_get_property), (no_more_pads_cb),
(autoplug_select_cb), (gst_play_bin_change_state):
Merge mode with flags.
Add more property getters/setters, defaults and docs.
Add properties to get number of audio/video/text streams.
Create sink object in _init so that we can always rely on it being
there.
* gst/playback/gstplaysink.c: (gst_play_sink_init),
(gen_video_chain), (gen_audio_chain), (gen_vis_chain),
(activate_vis), (gst_play_sink_reconfigure),
(gst_play_sink_set_flags), (gst_play_sink_get_flags),
(gst_play_sink_change_state):
* gst/playback/gstplaysink.h:
Use flags to configure the sink pipelines.
Add tee before audio pipeline so that we can use it for visualisations.
Start working on integrating visualisations.
Remove mode, we can do everything with the flags now.
Add method to configue the sink pipeline.
Original commit message from CVS:
* ext/pango/gsttextoverlay.c: (gst_text_overlay_class_init):
* gst/playback/gstplaybasebin.c: (set_subtitles_visible),
(set_active_source):
* gst/playback/gstplaybasebin.h:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init),
(setup_sinks), (playbin_set_subtitles_visible):
Make switching off of subtitles work. To avoid all kind of
problems with unlinking of the subtitle input, we just keep
the subtitle inputs linked as they are and tell textoverlay
not to render them. Fixes#373011.
Other subtitle switching issues (esp. when there are both
external and in-stream subtitles) remain. They'll be solved
in playbin2.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (gst_queue_init), (gst_queue_finalize),
(reset_rate_timer), (update_in_rates), (update_out_rates),
(gst_queue_locked_enqueue), (gst_queue_locked_dequeue),
(gst_queue_chain), (gst_queue_loop):
Use separate timers for input and output rates.
Pause measuring the output rate when we block for more data.
See #503262.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (gst_queue_chain):
Pause the timer to measure the input rate when we block because the
queue is filled. See #503262.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (analyze_new_pad), (connect_pad):
Expose the right pad in the right place with the right element.
Original commit message from CVS:
* gst/playback/Makefile.am:
Group decodebin2 and uridecodebin into the same plugin so that they
can share the GEnumType.
* gst/playback/gstdecodebin2.c: (_gst_array_accumulator),
(_gst_select_accumulator), (gst_decode_bin_class_init),
(gst_decode_bin_init), (gst_decode_bin_autoplug_sort),
(gst_decode_bin_autoplug_select), (gst_decode_bin_autoplug_add),
(analyze_new_pad), (connect_pad), (gst_decode_bin_plugin_init):
Add signal to sort factories instead of the more awkward autoplug-select
signal.
Modify autoplug_select so that we can try, skip or expose the
autopluggin of an element on a pad.
* gst/playback/gstfactorylists.c: (compare_ranks),
(decoders_filter), (sinks_filter), (gst_factory_list_is_type),
(element_filter), (gst_factory_list_get_elements),
(gst_factory_list_debug), (gst_factory_list_filter):
* gst/playback/gstfactorylists.h:
Simplify the API, allow getting elements based on mask.
* gst/playback/gstplay-marshal.list:
Add some more marshallers.
* gst/playback/gstplaybin2.c: (init_group), (gst_play_bin_init),
(gst_play_bin_finalize), (pad_removed_cb), (autoplug_factories_cb),
(autoplug_select_cb), (activate_group):
Add support for managing non-raw sinks by providing a custom element and
sink list to decodebin2.
Try to plug non-raw sinks when decodebin2 using autoplug-select of
decodebin2.
* gst/playback/gstplaysink.c: (gen_video_chain), (gen_audio_chain),
(gst_play_sink_set_mode), (gst_play_sink_request_pad):
* gst/playback/gstplaysink.h:
Add support for raw and non-raw sinks.
Add support to force sinks selected by playbin2.
Don't plug raw converters for non-raw sinks.
* gst/playback/gsturidecodebin.c: (_gst_array_accumulator),
(_gst_select_accumulator), (gst_uri_decode_bin_class_init),
(proxy_autoplug_select_signal), (gst_uri_decode_bin_plugin_init),
(plugin_init):
Use right accumulators.
Proxy new signal.
Original commit message from CVS:
* gst/playback/gststreamselector.c: (gst_selector_pad_get_type),
(gst_selector_pad_class_init), (gst_selector_pad_init),
(gst_selector_pad_finalize), (gst_selector_pad_reset),
(gst_selector_pad_get_linked_pads), (gst_selector_pad_event),
(gst_selector_pad_getcaps), (gst_selector_pad_bufferalloc),
(gst_selector_pad_chain), (gst_stream_selector_get_type),
(gst_stream_selector_base_init), (gst_stream_selector_class_init),
(gst_stream_selector_init), (gst_stream_selector_set_property),
(gst_stream_selector_get_linked_pad),
(gst_stream_selector_getcaps),
(gst_stream_selector_is_active_sinkpad),
(gst_stream_selector_activate_sinkpad),
(gst_stream_selector_get_linked_pads),
(gst_stream_selector_request_new_pad),
(gst_stream_selector_release_pad):
* gst/playback/gststreamselector.h:
Improve streamselector, make it select and unselect the current pad more
intelligently.
Subclass GstPad for the sinkpads of the selector.
Handle segments more correctly.
Fix caps negotiation.
Implement release_pad.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_class_init),
(gst_decode_group_check_if_drained), (source_pad_event_probe),
(remove_fakesink):
Add drained signal fired when decodebin finishes decoding the data.
Remove deprecated STATE_DIRTY message.
* gst/playback/gsturidecodebin.c: (gst_uri_decode_bin_class_init),
(unknown_type_cb), (new_decoded_pad_cb), (pad_removed_cb),
(analyse_source), (proxy_drained_signal), (make_decoder),
(source_new_pad), (value_list_append_structure_list),
(handle_redirect_message), (handle_message):
Proxy the new drained signal.
Handle pad removed from decodebin.
Handle redirect messages by sorting multiple redirections based on the
connection speed.
Original commit message from CVS:
* docs/design/design-decodebin.txt:
* gst/playback/gstdecodebin2.c: (analyze_new_pad):
Update some more docs and comments.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (queue_threshold_reached),
(finish_source):
Avoid crash when there are external subtitles (fixes#491722).
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (close_pad_link), (type_found):
* gst/playback/gstdecodebin2.c: (analyze_new_pad):
Post nice/more useful error message if we don't have a decoder for
the primary type.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_group_expose):
Be a bit more useful, unblock the pads after we fired the no-more-pads
signal so that we can use the signal to inspect and connect all pads
without having to keep extra state outside of decodebin.
Original commit message from CVS:
* gst/playback/gsturidecodebin.c:
(gst_uri_decode_bin_autoplug_continue),
(gst_uri_decode_bin_class_init), (no_more_pads_full):
Implement default signal handler so that we return TRUE when nothing is
connected.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_class_init),
(gst_decode_bin_dispose), (gst_decode_bin_set_caps),
(gst_decode_bin_set_subs_encoding),
(gst_decode_bin_get_subs_encoding), (gst_decode_bin_set_property),
(gst_decode_bin_get_property), (analyze_new_pad):
Move subtitle encoding property to decodebin2 so that it can set the
property value on all elements that it autoplugs and that require it.
Make caps refcounting more consistent in get/set.
* gst/playback/gsturidecodebin.c: (_gst_boolean_accumulator),
(gst_uri_decode_bin_class_init), (gst_uri_decode_bin_init),
(gst_uri_decode_bin_finalize), (gst_uri_decode_bin_set_property),
(gst_uri_decode_bin_get_property), (proxy_unknown_type_signal),
(proxy_autoplug_continue_signal),
(proxy_autoplug_factories_signal), (proxy_autoplug_select_signal),
(make_decoder):
Proxy properties and relevant signals from the internal decodebin.
Make properties MT safe.
Original commit message from CVS:
Inspired by patch of: René Stadler <mail at renestadler dot de>
* gst/playback/gstdecodebin2.c: (gst_decode_bin_class_init),
(gst_decode_bin_autoplug_continue),
(gst_decode_bin_autoplug_factories),
(gst_decode_bin_autoplug_select), (analyze_new_pad), (connect_pad),
(find_compatibles):
* gst/playback/gstplay-marshal.list:
Remove the autoplug-sort signal and replace it with a binding friendly
autoplug-select signal.
Add an autoplug-factories signal that can be used to generate a list of
factories to try to autoplug.
Add the GstPad to the autoplugging signal args as it might be needed to
make a good factory selection.
Fix up the marshallers for this. Fixes#407282.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (new_pad), (type_found):
Make the window for a race in typefind and shutting down smaller until
we figure out the right locking here. Avoids #485753 usually.
* gst/playback/gstdecodebin2.c: (type_found), (pad_added_group_cb):
Remove unneeded lock causing a race in typefind and shutting down.
Fixes#485753.
* gst/playback/gstplaybin.c: (gst_play_bin_change_state):
Also remove sinks when going to NULL because we might not complete the
state change to PAUSED, causing the PAUSED->READY state change not to
happen.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (type_found),
(gst_decode_bin_change_state):
* gst/playback/gstdecodebin2.c: (type_found),
(gst_decode_bin_change_state):
Don't disconnect the have_type signal because we never reconnect it
later on. Instead keep a variable to see if we already detected a type.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (add_fakesink), (type_found):
* gst/playback/gstdecodebin2.c: (gst_decode_bin_init),
(type_found):
Unlink the signal handler when we found the type, we're not going to do
anything sensible with more type_found signals anyway.
Original commit message from CVS:
* ext/pango/gsttextoverlay.c: (gst_text_overlay_init),
(gst_text_overlay_set_property):
* ext/vorbis/vorbisdec.c: (vorbis_handle_data_packet):
* gst-libs/gst/audio/gstbaseaudiosink.c:
(gst_base_audio_sink_render):
* gst-libs/gst/rtp/gstrtcpbuffer.c: (gst_rtcp_ntp_to_unix),
(gst_rtcp_unix_to_ntp):
* gst-libs/gst/rtsp/gstrtspmessage.c: (gst_rtsp_message_get_type):
* gst/playback/gstqueue2.c:
* tests/examples/seek/seek.c: (set_scale):
Fix a bunch of compile warnings shown with Forte.
* gst/audiorate/gstaudiorate.c:
Always pull in config.h before including any system headers.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (update_buffering),
(gst_queue_locked_flush), (gst_queue_locked_enqueue),
(gst_queue_handle_sink_event), (gst_queue_chain),
(gst_queue_push_one), (gst_queue_sink_activate_push),
(gst_queue_src_activate_push), (gst_queue_src_activate_pull):
Also fix#476514 for queue2.
Original commit message from CVS:
Patch by: Josep Torra Valles <josep@fluendo.com>
* gst/playback/gstplaybasebin.c:
Increase upper limit for audio queue a bit; fixes preroll problem
with playbin and decodebin2 when playing a quicktime trailer with
multichannel audio via http (#464666).
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (close_pad_link):
We need to set up delayed-linking whenever the caps are non-fixed,
not just when there are multiple types - use gst_pad_is_fixed()
to test.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_commit),
(queue_remove_probe), (queue_threshold_reached):
Patch by: Josep Torra Valles <josep@fluendo.com>
Fixes: #465015
Make sure we remove the check_queues buffer probe from the
correct queue to avoid racily going back to "buffering 99%" when
buffering is actually complete.
Also, fix the spelling of Josep's surname in the ChangeLog.
Original commit message from CVS:
Patch by: Josep Torre Valles <josep@fluendo.com>
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_class_init),
(gst_play_base_bin_init), (queue_threshold_reached),
(gen_source_element), (setup_substreams),
(gst_play_base_bin_set_property), (gst_play_base_bin_get_property),
(gst_play_base_bin_get_streaminfo_value_array):
* gst/playback/gstplaybasebin.h:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init),
(gst_play_bin_set_property), (gst_play_bin_get_property),
(gst_play_bin_handle_redirect_message):
Move connection-speed property from playbin to playbasebin so that we
can also configure it in source elements that have the connection-speed
property. Fixes#464028.
Add some debug info here and there.
Original commit message from CVS:
Patch by: Dan Williams <dcbw at redhat dot com>
* gst/playback/gstplaybasebin.c:
(gst_play_base_bin_get_streaminfo_value_array):
Don't return NULL when querying the stream info value array but instead
return an empty array. Fixes#459204.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (no_more_pads_full),
(setup_source):
Clear the dynamic pads counter when starting a new uri. This makes
reusing playbin work again.
Fixes#454264.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (apply_segment), (update_buffering):
Use other metrics as well when estimating the buffer level.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (make_decoder), (setup_source):
Small debug improvement.
* gst/playback/gstqueue2.c: (apply_segment), (update_buffering),
(plugin_init):
Tweak the rate estimation period.
When calculating the buffer filledness in rate estimation mode, don't
mix it with other metrics.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_group_new),
(gst_decode_group_expose), (gst_decode_group_free), (add_fakesink):
When creating the groups, allow for a 5 second, unlimited buffers
preroll phase after which we expose the group.
When the group is exposed, use a small number of buffers up to a 2
second limit. Also disconnect the overrun signal from multiqueue when we
exposed the group because it is not needed anymore.
Original commit message from CVS:
* ext/ogg/gstoggdemux.c: (gst_ogg_demux_find_chains):
The chain should be freed if we error out here, else it will leak.
* gst/playback/gstdecodebin.c: (disconnect_unlinked_signals),
(cleanup_decodebin):
Don't forget to *properly* remove the signals, else it will leak.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (analyze_new_pad):
When handling a delayed-caps notification case, mark
the group as dynamic so that the nbdynamic count is
incremented and decremented correctly. Fixes: #449156
Patch by: Wim Taymans <wim@fluendo.com>
Original commit message from CVS:
Patches by: Thiago Sousa Santos <thiagossantos at gmail dot com>
* gst/playback/gstqueue2.c: (update_buffering),
(gst_queue_locked_enqueue):
Fix a division by zero when the max percent is <= 0. Fixes#446572.
also update the buffering status when receiving events. Fixes#446551.
Original commit message from CVS:
Based on patch by: Thiago Sousa Santos <thiagossantos at gmail dot com>
* gst/playback/gstqueue2.c: (gst_queue_peer_query),
(gst_queue_handle_src_query):
Wait for preroll before attempting to forward a duration query upstream.
Fixes#445505.
Original commit message from CVS:
Patch by: Thiago Sousa Santos <thiagossantos at gmail dot com>
* gst/playback/gstqueue2.c: (gst_queue_init),
(gst_queue_handle_sink_event), (gst_queue_chain),
(gst_queue_get_range), (gst_queue_src_checkgetrange_function),
(gst_queue_sink_activate_push), (gst_queue_src_activate_push),
(gst_queue_src_activate_pull):
Add pull based scheduling and fix some deadlocks. Fixes#444523.
Does not yet completely work because duration queries upstream won't
block yet.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (gst_queue_have_data),
(gst_queue_create_read), (gst_queue_read_item_from_file),
(gst_queue_open_temp_location_file), (gst_queue_locked_enqueue):
Include stdio to define fseeko.
Original commit message from CVS:
* gst/playback/gsturidecodebin.c: (no_more_pads_full),
(new_decoded_pad), (remove_pads), (make_decoder), (setup_source),
(gst_uri_decode_bin_change_state):
Make sure we name srcpads uniquely even when using different internal
decodebins.
Signal no-more-pads when no more dynamic elements exist.
Remove pads on cleanup.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_factory_filter),
(analyze_new_pad), (connect_pad), (expose_pad), (caps_notify_cb),
(caps_notify_group_cb), (gst_decode_group_new),
(gst_decode_group_free):
Add support for delayed caps fixation when autoplugging.
Optimize cases where a multiqueue is not needed/wanted, like right after
anything that is not a demuxer.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (queue_overrun),
(no_more_pads_full):
Stop buffering when the group is commited because the queues filled up.
Fixes#442024.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (new_decoded_pad_full):
Handle unknown or invalid pads without crashing, as might occur if
a media file like an mp3 is specified as a subtitle file.
Fixes: #410039
Original commit message from CVS:
* gst/playback/gstplaybin.c: (add_sink), (dummy_blocked_cb),
(setup_sinks):
Block the subtitle bin output queue before ghosting it and linking,
then unblock after. This avoids spurious not-linked errors caused
by the queue starting up (because it gets linked when it is ghosted).
Fixes: #350299
Original commit message from CVS:
* ext/cdparanoia/gstcdparanoiasrc.c:
(gst_cd_paranoia_src_read_sector):
* gst-libs/gst/audio/gstbaseaudiosrc.c:
(gst_base_audio_src_create):
Small cleanups.
* ext/theora/theoradec.c: (theora_dec_sink_event):
Fix typo.
* gst-libs/gst/rtp/gstbasertpdepayload.c:
(gst_base_rtp_depayload_set_gst_timestamp):
Add some FIXME
* gst/playback/gstdecodebin.c: (queue_underrun_cb):
And some debug info when a FIXME path is hit.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_factory_filter):
Make decodebin2 autoplug depayloaders too.
* gst/playback/gsturidecodebin.c: (source_new_pad):
Set the newly created decoder in a usable state when autoplugging a
dynamic source such as RTSP.
Original commit message from CVS:
* gst/playback/gststreaminfo.c: (cb_probe):
Ignore video-codec tag for audio streams and ignore audio-codec tags
for video streams. Should make codec name collection a bit more
robust against sloppy demuxers that send tag events containing both
tags down each pad.
Original commit message from CVS:
* gst/playback/gstqueue2.c: (update_rates):
Tweak the buffering thresholds a little.
Update the buffer size with the previously calculate rate instead of
only when we calculate a new rate so that we get smoother buffering
updates.
* gst/playback/Makefile.am:
* gst/playback/gsturidecodebin.c: (gst_uri_decode_bin_base_init),
(gst_uri_decode_bin_class_init), (gst_uri_decode_bin_init),
(gst_uri_decode_bin_finalize), (gst_uri_decode_bin_set_property),
(gst_uri_decode_bin_get_property), (unknown_type),
(add_element_stream), (no_more_pads_full), (no_more_pads),
(source_no_more_pads), (new_decoded_pad), (array_has_value),
(gen_source_element), (has_all_raw_caps), (analyse_source),
(remove_decoders), (make_decoder), (remove_source),
(source_new_pad), (setup_source), (decoder_query_init),
(decoder_query_duration_fold), (decoder_query_duration_done),
(decoder_query_position_fold), (decoder_query_position_done),
(decoder_query_latency_fold), (decoder_query_latency_done),
(decoder_query_seeking_fold), (decoder_query_seeking_done),
(decoder_query_generic_fold), (gst_uri_decode_bin_query),
(gst_uri_decode_bin_change_state), (plugin_init):
New element that intergrates a source, optional buffering element and
decodebin.
Original commit message from CVS:
* gst/playback/Makefile.am:
* gst/playback/gstqueue2.c: (gst_queue_get_type),
(gst_queue_class_init), (gst_queue_init), (gst_queue_finalize),
(gst_queue_getcaps), (gst_queue_bufferalloc),
(gst_queue_acceptcaps), (update_time_level), (apply_segment),
(apply_buffer), (update_buffering), (reset_rate_timer),
(update_rates), (gst_queue_locked_flush),
(gst_queue_locked_enqueue), (gst_queue_locked_dequeue),
(gst_queue_handle_sink_event), (gst_queue_is_empty),
(gst_queue_is_filled), (gst_queue_chain), (gst_queue_push_one),
(gst_queue_loop), (gst_queue_handle_src_event),
(gst_queue_handle_src_query), (gst_queue_sink_activate_push),
(gst_queue_src_activate_push), (gst_queue_change_state),
(gst_queue_set_property), (gst_queue_get_property), (plugin_init):
On our way to playbin2 this is the new network queue that does buffering
all by itself using high and low watermarks. It can also measure up and
downstream bandwidth to optimally size the queue.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (fill_buffer), (check_queue),
(queue_out_of_data):
Connect to the new queue "pushing" signal instead of the broken
"running" one.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (type_found), (plugin_init):
* gst/playback/gstdecodebin2.c: (plugin_init):
Better error message for text files.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (add_sink),
(gst_play_bin_change_state):
Activate sync in playbin, we are ready to handle it for live streams.
Original commit message from CVS:
Patch by: Tommi Myöhänen <ext-tommi dot myohanen at nokia dot com>
* gst/playback/gstplaybasebin.c: (add_stream):
Fix leak in add_stream(), when g_value_set_object() increases the
refcount of streaminfo object. Fixes#426250.
Original commit message from CVS:
Patch by: Tommi Myöhänen <ext-tommi dot myohanen at nokia dot com>
* gst/playback/gstdecodebin2.c: (connect_pad), (expose_pad),
(deactivate_free_recursive):
Decodebin2 doesn't unref pads it obtains in some occasions:
- multiqueue src pads, when either connecting further or exposing
- sink pads of new autoplugged elements
- peer pads when recursively freeing elements
Fixes#425455.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init):
Remove playbin's override of the set_clock vmethod. It's irrelevant
after Wim's commit on the 19th.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (remove_fakesink):
Don't post STATE_DIRTY anymore.
* gst/playback/gstplaybin.c: (add_sink), (gst_play_bin_send_event),
(gst_play_bin_change_state):
Remove stream_time reset in seek handling, core does that now.
Disable clocking for live pipelines by forcing a NULL clock to the
complete pipeline, core is too smart now for our previous hack.
We can always autoplug in PAUSED now.
Original commit message from CVS:
* docs/plugins/Makefile.am:
* docs/plugins/gst-plugins-base-plugins-docs.sgml:
* docs/plugins/gst-plugins-base-plugins-sections.txt:
* docs/plugins/inspect/plugin-decodebin2.xml:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_class_init):
Add documentation for decodebin2 that indicates that the API
is still unstable.
Original commit message from CVS:
Patch by: Ed Catmur <ed at catmur dot co dot uk>
* gst/playback/gstplaybin.c: (gst_play_bin_vis_unblocked),
(gst_play_bin_vis_blocked), (gst_play_bin_set_property):
Fix race condition when rapidly switching visualisations in playbin.
Fixes#401029.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_dispose),
(multi_queue_underrun_cb), (gst_decode_group_check_if_drained),
(sort_end_pads), (gst_decode_group_expose),
(gst_decode_group_hide):
Don't free groups from the streaming threads. Just put them aside and
free them in dispose.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (connect_element),
(pad_added_group_cb), (gst_decode_group_check_if_blocked),
(sort_end_pads), (gst_decode_group_expose):
Handle dynamic pads within groups.
Sort pads before exposing them in order to make playbin happy.
There still is a race with the multiqueue filling up. This should be
solved separately.
Fixes#398721
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (setup_source):
When we have external subtitles and wait for the subtitle decodebin
to get up and running, we set up a (sync) bus handler for the
subtitle decodebin, so we can stop waiting when it posts an error
message. However, we should do that before we set the subtitle
decodebin's state to playing, otherwise things are racy and we might
miss error messages posted before we had a chance to set up the bus.
This should finally fix totem hanging on .txt pseudo-subtitle files.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (add_fakesink),
(gst_decode_bin_change_state):
* gst/playback/gstdecodebin2.c: (add_fakesink),
(gst_decode_bin_change_state):
Don't error out if there is no fakesink in the READY to NULL state
change, since when decodebin is re-used, we're only adding the
fakesink element in READY to PAUSED.
* tests/check/elements/decodebin.c:
(new_decoded_pad_plug_fakesink_cb), (GST_START_TEST),
(decodebin_suite):
Minimal unit test to make sure we can use the same decodebin
instance twice (at least with audiotestsrc input).
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_vis_element):
Add audioresample+audioconvert in front of the visualisation
element, so that elements like libvisual 0.4 that don't support all
samplerates can work.
Fixes: #402505
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_get_property),
(gst_play_base_bin_get_streaminfo_value_array):
Take some locks and make a copy of the streaminfo value array we
maintain while holding the lock, so that the application can
retrieve the stream-info as a value array in a thread-safe way.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_dispose):
Cast lock macro parameters to make sure we're actually accessing the
lock member at the right class level. Free list itself in _dispose()
as well and NULL it in case dispose gets called multiple times.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c:
(gst_decode_bin_dispose),(gst_decode_bin_finalize):
Free GstDecodeGroups no longer used.
(gst_decode_group_expose):
Don't unlock too many times !
(deactivate_free_recursive):
Free iterator once we're done with it.
Fix for recursively deactivating elements (stop at ghostpads).
Original commit message from CVS:
* gst/playback/gstplaybin.c: (handoff):
Fix up caps on the frame buffer before we save it and potentially
make it accessible to other threads via g_object_get; also use
gst_buffer_replace() instead of gst_mini_object_replace().
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_finalize),
(gst_decode_group_new), (gst_decode_group_free):
Set queues to bigger sizes to cope with HD contents.
Fix some mutex freeing and add comment about MT safe methods.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_bin_finalize):
Don't leak mutex.
* tests/check/elements/playbin.c:
(test_sink_usage_video_only_stream),
(test_suburi_error_unknowntype), (test_suburi_error_invalidfile),
(test_suburi_error_wrongproto), (test_missing_urisource_handler),
(test_missing_suburisource_handler),
(test_missing_primary_decoder), (playbin_suite):
Run all tests once with decodebin and once with decodebin2.
One test does not pass yet with decodebin2.
Original commit message from CVS:
* gst/playback/gstdecodebin2.c: (gst_decode_group_new),
(get_current_group), (group_demuxer_event_probe),
(gst_decode_group_expose), (deactivate_free_recursive),
(gst_decode_group_free):
Cleanups.
Don't forget to emit 'no-more-pads' once a group is exposed.
Cleanup elements from a DecodeGroup once we remove it.
Protect call to gst_decode_group_expose() with the decodebin lock.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (setup_subtitle),
(gen_source_element), (gst_play_base_bin_change_state):
Attempt at a better error message in case we don't have the required
URI handler installed; post missing-plugin message also when we're
missing an URI handler for the subtitle URI; clean up properly also
when an error occurs and we never made it to PAUSED state.
* tests/check/elements/playbin.c: (GST_START_TEST),
(playbin_suite):
Check that we're also getting a missing-plugin messsage for a
missing subtitle URI handler (and clean up properly).
Original commit message from CVS:
* gst/playback/Makefile.am:
* gst/playback/gstdecodebin.c: (close_pad_link):
* gst/playback/gstdecodebin2.c: (analyze_new_pad):
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_class_init),
(gst_play_base_bin_handle_message_func), (unknown_type):
Let decodebin be the element to post missing-plugin messages for
missing decoders (rather than playbin); make playbin implement
GstBin::handle_message so we can suppress missing-plugin messages
for types we're not handling on purpose (don't want to bring up an
installer in those cases).
Original commit message from CVS:
* gst/playback/gstplaybin.c: (post_missing_element_message),
(gen_video_element), (gen_text_element), (gen_audio_element),
(gen_vis_element):
Post missing-plugin messages also when we error out because
converters, textoverlay or auto*sinks are missing (#161922).
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (dynamic_add), (close_pad_link),
(is_demuxer_element), (new_caps):
* gst/playback/gstplaybasebin.c: (source_new_pad):
Fix the case where we try to ref a NULL element when we delay a link
because of unfixed caps.
Set the state of autoplugged decodebins to PAUSED.
RTSP now works in playbin, we can remove it from the blacklist.
Original commit message from CVS:
* gst/playback/Makefile.am:
* gst/playback/gstplaybasebin.c: (string_arr_has_str),
(unknown_type), (setup_subtitle), (gen_source_element):
* gst/playback/gstplaybin.c: (plugin_init):
Post missing-plugin messages on the bus for missing sources and
missing decoders/demuxers/depayloaders; fix error code used when
we're missing an URI handler source; for media types that we are not
handling on purpose at the moment, don't print "don't know how to
handle xyz" messages to the terminal or post missing-plugin
messages on the bus.
* tests/check/elements/playbin.c: (create_playbin),
(GST_START_TEST), (gst_codec_src_uri_get_type),
(gst_codec_src_uri_get_protocols), (gst_codec_src_uri_get_uri),
(gst_codec_src_uri_set_uri), (gst_codec_src_uri_handler_init),
(gst_codec_src_init_type), (gst_codec_src_base_init),
(gst_codec_src_create), (gst_codec_src_class_init),
(gst_codec_src_init), (plugin_init), (playbin_suite):
Add some tests for the missing-plugin stuff.
Original commit message from CVS:
* ext/ogg/gstoggdemux.c: (gst_ogg_pad_stream_out):
* ext/vorbis/vorbisdec.c: (vorbis_handle_data_packet):
* gst/playback/gstdecodebin2.c:
(gst_decode_group_check_if_blocked):
Printf format and missing argument fixes.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (type_found):
Special-case the text/plain media type: we only want to recognise it
as a 'raw' decoded media type if it comes from a demuxer or subtitle
parser, but not if the entire stream is of text/plain type. If the
entire stream is text/plain, we should just error out.
This fixes playback of audio files with lyrics in totem. Totem can't
distinguish between text files and subtitle files and passes any
.txt file with the same basename as the main file to playbin as
suburi, and playbin will then throw a 'subtitle found, but no video
stream' error, which isn't entirely helpful. See #380342.
Also, with this change we'll show a slightly more correct error
message in case totem passes a playlist file to us (although a
custom error message wording instead of the default text would
probably not be a bad idea either).
Same problem also needs to be fixed for playbin+decodebin2.
* tests/check/Makefile.am:
* tests/check/elements/decodebin.c: (src_handoff_cb),
(decodebin_new_decoded_pad_cb), (GST_START_TEST),
(decodebin_suite):
Add simple unit test for decodebin for the above.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_change_state):
* gst/playback/gstdecodebin2.c: (gst_decode_bin_change_state):
Refuse to change state to READY when we failed to create any of the
required elements in our instance init function.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (find_dynamic), (dynamic_add),
(close_pad_link), (elem_is_dynamic), (unlinked), (close_link):
Handle the case where an element has multiple pads with
unfixed caps as well as still possibly producing more dynamic
pads by storing each case as a distinct entry in the dynamic list.
Fixes#38223 again.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (check_queue_event):
Improve debug.
* gst/videoscale/gstvideoscale.c: (gst_video_scale_transform_caps):
Fix width and height range from 16 - 4096 to 1 - MAXINT, just like the
padtemplate caps. Refixes #357577.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (check_queue_event),
(queue_threshold_reached), (queue_out_of_data),
(gen_preroll_element):
Add event probe to see when EOS is in a queue and we can disable the
underrun signals. Fixes#357577.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (setup_source),
(gst_play_base_bin_change_state):
Disable rtsp:// uris for the release, it's not good enough yet.
Remove unused var.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (subbin_startup_sync_msg),
(setup_source):
Catch async errors when starting up the subtitle bin, so we can
stop waiting and continue with the main film instead of hanging
forever. Fixes#339366.
* tests/check/elements/playbin.c: (playbin_suite):
Enable unit test for the above.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (setup_source):
Don't hang forever if the subbin already fails to start up in
the state change to PAUSED (#339366).
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (get_our_ghost_pad),
(remove_element_chain):
Don't return a pad from get_our_ghost_pad unless it is actually the
one we want.
Change a cast in remove_element_chain slightly.
Original commit message from CVS:
* gst-libs/gst/audio/gstbaseaudiosink.c:
(gst_base_audio_sink_setcaps):
Don't crash when ringbuffer is not yet created.
Patch by: Ville Syrjala <ville dot syrjala at movial dot fi>
Fixes#361634.
* gst/playback/gstplaybasebin.c: (new_decoded_pad_full):
* gst/playback/gststreamselector.c:
(gst_stream_selector_request_new_pad):
Activate pads befre adding them to running elements.
Original commit message from CVS:
2006-10-10 Zaheer Abbas Merali <zaheerabbas at merali dot org>
Patch by: Josep Torre Valles <josep@fluendo.com>
* ext/gnomevfs/gstgnomevfssink.c:
* ext/gnomevfs/gstgnomevfssrc.c:
Fix URI interface implementation return type.
* ext/pango/gsttextoverlay.c: (gst_text_overlay_set_property):
Fix what looks like a copy/paste issue when assigning values.
* gst-libs/gst/audio/gstaudiofiltertemplate.c:
(gst_audio_filter_template_get_type):
Cast to prevent Forte warnings.
* gst-libs/gst/cdda/gstcddabasesrc.c: (gst_cdda_base_src_create):
Fix URI interface implementation return type.
gst_pad_query_position requires a signed integer pointer as
3rd parameter, GstClockTime is unsigned.
* gst/audioconvert/audioconvert.c:
Fix integer overflow when treated as signed.
* gst/audioresample/resample.c: (resample_add_input_data):
Cast to prevent warnings on Forte.
* gst/ffmpegcolorspace/imgconvert.c: (build_rgb_palette):
Fix integer overflow when treated as signed.
* gst/ffmpegcolorspace/imgconvert_template.h:
Fix integer overflow when treated as signed. RGBA_OUT shifts bits.
* gst/playback/gstdecodebin.c: (queue_filled_cb),
(cleanup_decodebin):
Who initialises a guint to -1!
Cast function pointers to prevent warnings on Forte.
* gst/playback/gstplaybasebin.c: (queue_deadlock_check),
(queue_threshold_reached):
Cast function pointers correctly to prevent warnings on Forte.
* gst/playback/gststreaminfo.c: (gst_stream_info_dispose):
Cast function pointers correctly to prevent warnings on Forte.
* gst/subparse/gstssaparse.c: (gst_ssa_parse_setcaps):
Obvious change to unsigned, 0xEF > max signed char.
* gst/tcp/gstmultifdsink.c: (get_buffers_max), (count_burst_unit):
GstClockTime is unsigned, initialise correctly.
* gst/tcp/gsttcp.c: (gst_tcp_socket_write):
Cast so pointer arithemetic doesn't cause warnings on Forte.
* gst/videorate/gstvideorate.c:
Use correct return value.
* tests/examples/seek/scrubby.c:
GstClockTime is unsigned, initialise correctly.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_init),
(close_pad_link):
* gst/playback/gstplaybasebin.c: (new_decoded_pad_full):
Activate dynamic pads before adding them to the element.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (close_pad_link):
Fix typo in a debug statement.
* gst/playback/gstplaybasebin.c: (probe_triggered),
(new_decoded_pad_full), (new_decoded_pad), (subs_new_decoded_pad),
(gen_source_element), (source_new_pad), (analyse_source),
(setup_source):
When handling no_more_pads in new_decoded_pad, make sure to treat
subtitle pads correctly. Fixes playback with subtitle files.
Move a recurring message to LOG level.
* sys/xvimage/xvimagesink.c: (gst_xvimagesink_get_xv_support):
The maximum value for the Xv colorkey on this Radeon is 0xFFFFFFFF,
which ends up as -1 when cast to an int. Make the logic handle the
max value as an unsigned mask and only change the colorkey when it's
a value we recognise.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (dynamic_create), (dynamic_free),
(close_pad_link), (dynamic_remove), (no_more_pads), (new_caps),
(find_dynamic), (unlinked), (close_link):
Implement delayed caps linking needed for element with a lot of
different caps on the src pads that get fixed at runtime.
Improve management of dynamic elements.
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_init),
(group_destroy), (group_commit), (check_queue), (queue_overrun),
(gen_preroll_element), (remove_groups), (unknown_type),
(add_element_stream), (no_more_pads_full), (no_more_pads),
(sub_no_more_pads), (source_no_more_pads), (preroll_unlinked),
(new_decoded_pad), (setup_subtitle), (array_has_value),
(gen_source_element), (source_new_pad), (has_all_raw_caps),
(analyse_source), (remove_decoders), (make_decoder),
(remove_source), (setup_source), (finish_source), (prepare_output),
(gst_play_base_bin_change_state):
* gst/playback/gstplaybasebin.h:
Use more _CAST instead of full type checking casts.
Small cleanups, plug some leaks.
Handle dynamic sources.
Add some helper functions to create lists of strings used for
blacklisting and other stuff.
Refactor some code dealing with analysing the source.
Re-enable sources without pads (like cd:// or other selfcontained
elements).
Original commit message from CVS:
* gst/playback/gstplaybin.c: (remove_sinks):
Only remove visualisation from visbin if there is a visbin (or:
don't throw warnings when closing totem without playing a file).
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_factory_filter),
(add_fakesink), (remove_fakesink), (pad_probe), (close_pad_link),
(is_demuxer_element), (try_to_link_1), (get_our_ghost_pad),
(new_pad):
Cleanups and small leak fixes.
Added Depayloaders to valid list of autopluggable elements.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init),
(gst_play_bin_vis_blocked), (gst_play_bin_set_property),
(gen_video_element), (gen_text_element), (gen_audio_element),
(gen_vis_element), (remove_sinks), (add_sink), (setup_sinks),
(gst_play_bin_set_clock_func), (gst_play_bin_change_state):
Detect NO_PREROLL state change returns and disable clock distribution to
the sinks so that sync is disabled.
Avoid some type checking and do simple casts instead.
Small cleanups, fix some FIXMEs.
Be more robust when linking user specified elements, catch an report
errors. Fixes#357404.
Fix some leaks in the error paths.
Original commit message from CVS:
Patch by: Peter Kjellerstedt <pkj at axis com>
* gst/playback/test.c:
Fix compilation with uClibc and -Werror (#357591).
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gen_preroll_element):
Improve buffering a bit by avoiding a deadlock because we cannot assume
the underrun is always called.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_commit),
(queue_deadlock_check), (queue_overrun), (queue_threshold_reached),
(queue_out_of_data), (gen_preroll_element),
(preroll_remove_overrun), (probe_triggered):
Refactor handling of overrun detection.
Separate handling of group completion and deadlock detection when doing
network buffering. This should fix some deadlocks that were not detected
because the group was completed.
Add more comments, improve debugging.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (get_active_source):
Make stream-switching appear instant to the application
(ie. make sure that a g_object_get on 'current-foo' returns
the stream previously set with g_object_set(). Totem needs
this to update stream-related meta-info (like audio-codec)
correctly when switching streams.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_class_init),
(gst_play_base_bin_init), (fill_buffer), (check_queue),
(queue_threshold_reached), (gst_play_base_bin_set_property),
(gst_play_base_bin_get_property):
* gst/playback/gstplaybasebin.h:
Don't use a 0 low watermark when buffering, it is catching starvation
way too late. Instead, use a 3 second queue with 30 and 95
percent low/high watermarks.
Added queue-min-threshold property to configure low watermark.
Use new _buffering message API.
Make queue_threshold variable big enough to store a uint64 time value.
API: playbin::queue-min-threshold property.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init),
(gst_play_bin_set_property), (gst_play_bin_get_property),
(value_list_append_structure_list),
(gst_play_bin_handle_redirect_message),
(gst_play_bin_handle_message):
Add "connection-speed" property; re-order redirect messages with
multiple redirect locations depending on the minimum bitrate if
that information is available and a connection speed is set
(#350399).
Original commit message from CVS:
* gst/playback/test.c: (gen_video_element), (gen_audio_element),
(cb_newpad), (main):
Example of a small audio/video player using decodebin.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (find_compatibles):
Fix a caps leak when linking (#347304)
* sys/ximage/ximagesink.c: (gst_ximage_buffer_finalize),
(gst_ximagesink_ximage_destroy), (gst_ximagesink_xcontext_clear),
(gst_ximagesink_change_state):
* sys/xvimage/xvimagesink.c: (gst_xvimage_buffer_destroy),
(gst_xvimage_buffer_finalize), (gst_xvimagesink_check_xshm_calls),
(gst_xvimagesink_xvimage_new), (gst_xvimagesink_xvimage_put),
(gst_xvimagesink_xcontext_clear), (gst_xvimagesink_change_state):
Don't leak shared memory resources. Use the object lock to protect
against the xcontext disappearing while returning a buffer from the
pipeline. (#347304)
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (close_pad_link):
Also emit 'unknown-type' signal (which should really be
called unhandled-type) if we found potential decoders/demuxers
in the registry but none of them worked in the end (as in the
case where the plugins don't exist any longer but are still
listed in the registry). Fixes#329798.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_init),
(gst_play_base_bin_finalize), (decodebin_element_added_cb),
(decodebin_element_removed_cb), (gst_play_base_bin_set_property):
* gst/playback/gstplaybasebin.h:
Protect list of elements with a subtitle-encoding property and
the subtitle encoding member itself with a lock of their own
instead of using the object lock. This prevents a dead-lock in
the element-remove callback in some circumstances when shutting
down playbin.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (is_stream), (gen_source_element):
Improve checking if we are dealing with a stream. Added some
more uris that need buffering.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_class_init),
(gst_decode_bin_init), (gst_decode_bin_finalize), (add_fakesink),
(remove_fakesink), (pad_probe), (gst_decode_bin_change_state):
Protect remove_fakesink using a mutex, so that we don't try and
remove the fakesink simultaneously from multiple threads.
When going from READY to PAUSED, restore the fakesink, so that
it is there when decodebin gets reused.
Original commit message from CVS:
* gst/playback/gststreaminfo.c: (cb_probe):
Try GST_TAG_CODEC as fallback when extracting the
codec name; more debug info.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_create), (group_commit),
(setup_source):
* gst/playback/gstplaybasebin.h:
Make the subtitle detection work from any thread so we don't
deadlock. Fixes#343397.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gen_source_element):
Throw a more comprehensible error for rtsp:// URIs (rather
than erroring out with a negotiation error later on) until
we fix playbin to handle rtspsrc etc.
Original commit message from CVS:
Patch by: Young-Ho Cha <ganadist at chollian net>
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_class_init),
(gst_play_base_bin_init), (gst_play_base_bin_dispose),
(set_encoding_element), (decodebin_element_added_cb),
(decodebin_element_removed_cb), (setup_subtitle), (setup_source),
(gst_play_base_bin_set_property), (gst_play_base_bin_get_property):
* gst/playback/gstplaybasebin.h:
Add 'subtitle-encoding' property to playbin, so applications can
force a subtitle encoding for non-UTF8 subtitles (#342268).
* gst/subparse/gstsubparse.c: (gst_sub_parse_class_init),
(gst_sub_parse_set_property):
Rename recently-added 'encoding' property to 'subtitle-encoding'
(so it can be proxied by playbin/decodebin in a generic way
with less danger of false positives).
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (remove_fakesink), (pad_probe):
When there is only one unfinished pad and it receives an event that
doesn't match our requirements, we need to set alldone=FALSE so that
the fakesink is not removed yet.
Original commit message from CVS:
2006-05-15 Julien MOUTTE <julien@moutte.net>
* gst/playback/gstdecodebin.c: (cleanup_decodebin),
(gst_decode_bin_change_state): Make decodebin reusable
when going from PAUSE_TO_READY and then back to PAUSED.
Fixes#331678.
Original commit message from CVS:
2006-05-11 Thomas Vander Stichele <thomas at apestaart dot org>
patch by: Sjoerd Simons (sjoerd@luon.net)
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_class_init),
(group_create), (group_destroy), (add_stream),
(gst_play_base_bin_get_property),
(gst_play_base_bin_get_streaminfo_value_array):
* gst/playback/gstplaybasebin.h:
API: GstPlayBaseBin::stream-info-value-array property
use a more bindings-friendly way of exposing streaminfo
using a GValueArray. Tested in ipython.
Closes#341114
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (try_to_link_1), (queue_enlarge),
(queue_underrun_cb), (queue_filled_cb):
Also catch queue underruns but don't do anything yet.
Refactor and comment queue enlarging code a bit.
* gst/playback/gstplaybasebin.c: (queue_overrun),
(queue_threshold_reached), (queue_out_of_data),
(gen_preroll_element):
If a queue over/underruns check that we don't create nasty
deadlocks when the min-threshold is not reached but the
max-bytes is. In those cases disable max-bytes when we
know that the queue is fed timed data.
Add more comments.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_audio_element):
Make playbin automatically plug an 'audioresample'
element before the audio sink as well. This solves
problems with sinks that only accept a very specific
sample rate, like esdsink (e.g. #340379).
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gen_source_element):
Make http sources send special headers so that we receive
icecast metadata if the http stream is an icecast stream
(otherwise the server will just ignore them). This also
means that from now on users will need the 'icydemux'
element from gst-plugins-good installed if they want to
listen to icecast radio streams. (#341432, #333657).
Original commit message from CVS:
Patch by: Jan Schmidt
* gst/playback/gststreamselector.c:
(gst_stream_selector_bufferalloc):
Restore old StreamSelector behaviour.
Fixes#338419.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_destroy):
Clean up our group elements properly in the case where it never
got committed - it still got added unconditionally to the bin.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (mute_stream), (setup_substreams):
Don't remove our mute-probe if someone else already did so.
Don't set a 2nd one if there is already one pending on the pad.
* gst/playback/gstplaybin.c: (gst_play_bin_send_event_to_sink),
(do_playbin_seek):
When a seek fails, ensure that playbin is still set back to playing.
* gst/typefind/gsttypefindfunctions.c: (mpeg_ts_probe_headers),
(mpeg_ts_type_find), (plugin_init):
Add a typefind function for mpeg-ts streams.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_video_element),
(gen_text_element), (gen_audio_element), (gen_vis_element):
Error out gracefully when we can't create any of the usual
conversion elements for some reason. Also, don't try to
create an audioscale (sic) element that's not used anyway.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (setup_source):
Don't post RESOURCE_NOT_FOUND error when we can't find a source
element for a particular protocol, that's confusing for users.
Instead, post a RESOURCE_FAILED error, so that our own error
message is actually shown in totem etc. (#336303).
Original commit message from CVS:
* gst/playback/gststreamselector.c:
(gst_stream_selector_set_property),
(gst_stream_selector_bufferalloc):
Preserve the existing buggy streamselector behaviour by performing
a fallback buffer allocation when downstream isn't linked yet.
This should really be fixed in playbin by blocking pads until it's
linked them.
Also, use gst_pad_alloc_buffer instead of
gst_pad_alloc_buffer_and_set.
Original commit message from CVS:
* ext/alsa/gstalsasink.c: (gst_alsasink_finalise):
Chain up to the parent finalize method.
Add 32-bit sample size to the template caps.
* gst-libs/gst/riff/riff-media.c: (gst_riff_create_video_caps),
(gst_riff_create_video_template_caps):
Add the fourcc that the VMWare codec uses.
* gst/playback/gststreamselector.c:
(gst_stream_selector_set_property),
(gst_stream_selector_bufferalloc),
(gst_stream_selector_request_new_pad):
For the active pad, forward buffer-alloc requests, otherwise
return GST_FLOW_NOT_LINKED. This also prevents xvimagesink
having to memcpy every frame when used by playbin.
* gst/tcp/gstmultifdsink.c:
(gst_multi_fd_sink_handle_client_write):
Get negotiated caps from the sink pad, rather than the sink
pad's peer.
Original commit message from CVS:
* ext/gnomevfs/gstgnomevfssrc.c: (gst_gnome_vfs_src_create):
Don't send EOS event here, the base class will send one for us.
* gst/playback/gstplaybasebin.c: (prepare_output):
Subpictures without video stream aren't allowed either.
* gst/subparse/gstsubparse.c: (gst_subparse_type_find):
Fix debug statement copy'n'paste-o.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (get_our_ghost_pad),
(remove_element_chain), (cleanup_decodebin),
(gst_decode_bin_change_state): Make decodebin reusable by
fixing remove_element_chain first and then introduce a
cleaner in state change to ->NULL. (Closes#331678)
------------------------------------------------------
Original commit message from CVS:
2006-02-19 Julien MOUTTE <julien@moutte.net>
* gst/playback/gstdecodebin.c: (mimetype_is_raw): pango layout
should be considered as row.
Original commit message from CVS:
2006-02-18 Julien MOUTTE <julien@moutte.net>
* ext/pango/gsttextoverlay.c: (gst_text_overlay_base_init),
(gst_text_overlay_finalize), (gst_text_overlay_init),
(gst_text_overlay_setcaps), (gst_text_overlay_src_event),
(gst_text_overlay_render_text),
(gst_text_overlay_text_pad_link),
(gst_text_overlay_text_pad_unlink),
(gst_text_overlay_text_event),
(gst_text_overlay_video_event), (gst_text_overlay_pop_text),
(gst_text_overlay_text_chain), (gst_text_overlay_video_chain),
(gst_text_overlay_change_state): Refactoring of textoverlay
without collectpads. This now supports sparse subtitles coming
from a demuxer instead of a sub file. Seeking is still broken
though. Need to discuss with wtay some more on how to handle
seeking correctly.
* ext/pango/gsttextoverlay.h:
* gst/playback/gstplaybin.c: (setup_sinks): Support linking with
subtitles coming from the demuxer.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_vis_element):
Update vis bin docs.
Move queue after tee so we don't queue video buffers but
audio samples instead. Fixes problems where the video queue
is filled and the audio queue empty.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (prepare_output):
Don't print the URI as part of the error message, it
makes error dialogs look rather ugly, especially if
the URI is very long or has characters in it that
need escaping.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (prepare_output):
Error out if we have only text or subtitles, but nothing
else. Also error out if we have subtitles but no video
stream.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (try_to_link_1):
Don't put essential function call into
g_return_*() macro, otherwise it'll all be
replaced by NOOPs when compiling with
G_DISABLE_CHECKS defined.
Original commit message from CVS:
* gst/playback/test6.c: (new_decoded_pad_cb), (show_error), (main):
Make test work again by connecting fakesinks to each decoded pad,
which makes the pipeline wait until each fakesink has a buffer
queued before going to PAUSED state. At that point we know the
decodebin pads are negotiated.
Original commit message from CVS:
* gst-libs/gst/audio/audio.h: (GST_CLOCK_TIME_TO_FRAMES)
* gst-libs/gst/audio/gstbaseaudiosink.c: (gst_base_audio_sink_render)
use of gst_guint64_to_gdouble to be compliant with vs6
* gst/playback/gstdecodebin.c: (try_to_link_1)
* gst/videorate/videorate.c: (gst_video_rate_blank_data)
use of G_GINT64_CONSTANT for int64 constants
* win32/common/libgstinterfaces.def:
export some symbols (gst_mixer_get_type,gst_mixer_track_get_type)
* win32/vs6:
update and add new project files
Original commit message from CVS:
* ext/alsa/gstalsaplugin.c: (plugin_init):
* ext/cdparanoia/gstcdparanoiasrc.c:
(gst_cd_paranoia_src_base_init), (plugin_init):
* ext/gnomevfs/gstgnomevfs.c: (plugin_init):
* ext/ogg/gstoggdemux.c: (gst_ogg_demux_plugin_init):
- a library should not call setlocale. see Libraries node in
gettext manual
- make sure all plugins that use translation do bindtextdomain
to point to the localedir
* gst/playback/gstplaybin.c: (gen_vis_element), (add_sink),
(setup_sinks), (plugin_init):
all this, and check for NULL when creating sinks
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (pad_probe):
Also consider the flush-start and tag events as unblockers
for the pad probes.
Original commit message from CVS:
2006-01-26 Julien MOUTTE <julien@moutte.net>
* gst/playback/gstplaybin.c: (gst_play_bin_init),
(gst_play_bin_dispose), (gst_play_bin_vis_unblocked),
(gst_play_bin_vis_blocked), (gst_play_bin_set_property):
On the fly visualisation switch, works disabling, enabling as
well but it won't be able to enable vis in a playbin that was
created with no visualisation.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_init),
(free_pad_probes), (remove_fakesink), (pad_probe),
(close_pad_link), (gst_decode_bin_change_state):
Replace GstPadBlockCallback with pad probes that detect
first buffer AND eos before removing fakesink.
Fixes hang with demuxers doing EOS while pre-rolling.
Solves #328279
Original commit message from CVS:
* gst/playback/gststreaminfo.c: (gst_stream_info_set_mute):
* gst/playback/gststreamselector.c:
(gst_stream_selector_set_property):
Comment out broken code that connects to the state-changed signal.
At this point, changing current stream selection is broken, but
stuff like gst-launch playbin current-audio=1 works and filters
to the chosen stream.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (setup_source):
Fix playback for sources that emit raw audio or
raw video streams (e.g.: cd audio sources) (#325984).
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_destroy),
(probe_triggered), (new_decoded_pad), (mute_group_type),
(set_active_source):
* gst/playback/gststreaminfo.c: (gst_stream_info_set_mute):
* gst/playback/gststreamselector.c:
(gst_stream_selector_base_init),
(gst_stream_selector_set_property),
(gst_stream_selector_request_new_pad):
Reenable stream selection. These mechanisms need a complete overhaul
in the face of 0.8->0.10 changes though.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_audio_element):
Don't leak an autoaudiosink/alsasink when we generate
a new audio element. (old code, I guess)
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (new_pad):
Fix non-C89 variable declaration not at the start of a block. Should
help some compilers.
Original commit message from CVS:
* ext/ogg/gstoggdemux.c: (gst_ogg_demux_deactivate_current_chain),
(gst_ogg_demux_activate_chain):
Extra debug output when activating/deactivating chains.
* gst/playback/gstdecodebin.c: (gst_decode_bin_factory_filter),
(is_demuxer_element), (try_to_link_1), (remove_element_chain),
(unlinked):
Remove a queue from our list when it becomes unlinked.
Don't add queues to elements in class 'Demux' if they
can only produce one pad
Original commit message from CVS:
* gst/playback/gstplaybasebin.c:
* gst/playback/gstplaybin.c: (handoff):
Make sure the video frame buffer we return to apps via the
"frame" property always has caps set on it. Modify
_gst_gvalue_set_object() macro to handle NULL objects
gracefully too.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gst_play_base_bin_get_property):
* gst/playback/gstplaybin.c: (gst_play_bin_get_property):
Work around refcount problem with g_value_set_object() that occur
if the core has been compiled against GLib-2.6 (g_value_set_object()
will only g_object_ref() the element, but the caller will
gst_object_unref() it and bad things will happen due to the way
GstObjects are refcounted in the GLib-2.6 case). Fixes problems with
totem for people on FC4 using Thomas's 0.10 RPMs.
Original commit message from CVS:
* gst/playback/gststreamselector.c: (gst_stream_selector_chain):
3rd time's the charm. Correct ref-counting for discarded buffers.
Original commit message from CVS:
* gst/playback/gststreamselector.c:
(gst_stream_selector_class_init), (gst_stream_selector_init),
(gst_stream_selector_dispose), (gst_stream_selector_set_property),
(gst_stream_selector_get_property),
(gst_stream_selector_get_linked_pad),
(gst_stream_selector_request_new_pad), (gst_stream_selector_chain):
* gst/playback/gststreamselector.h:
Add the active-pad property for playbin to use shortly. Ignore buffers
from any other pad, returning GST_FLOW_NOT_LINKED
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_init),
(try_to_link_1), (queue_filled_cb):
Better use of the queues. Start with a small size queue and only increase
the size of the queues when the other queues are empty.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_commit), (probe_triggered):
* gst/playback/gstplaybasebin.h:
Prepare to handle errors betters.
* gst/playback/gstplaybin.c: (add_sink), (setup_sinks):
Set sinks to PAUSED first before adding and linking them so that
we don't interrupt dataflow.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_class_init),
(gst_decode_bin_init), (close_pad_link), (try_to_link_1):
Remove unused properties, and add queues between demuxers and decoders
so that a lot more files can preroll properly.
Original commit message from CVS:
2005-11-21 Andy Wingo <wingo@pobox.com>
* gst/playback/gstplaybin.c (gen_audio_element)
(gen_video_element): Use the new MISSING_PLUGIN core error
category.
Original commit message from CVS:
* gst-libs/gst/tag/Makefile.am:
* gst-libs/gst/tag/gstvorbistag.c:
(gst_tag_list_to_vorbiscomment_buffer):
Remove obsolete vorbistag element and debug category.
* gst/playback/gstplaybasebin.c: (check_queue):
Don't divide by 0 when queue-threshold is 0.
* sys/ximage/ximagesink.c: (gst_ximagesink_set_property):
Don't modify an existing pixel-aspect-ratio if we fail to read
a new one.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_init):
Unsetting IS_SINK flag from the fakesink, so decodebin
never behaves as a sink.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_audio_element):
Use autoaudiosink, it tends to be more widely available than
autoaudiiosink.
Original commit message from CVS:
2005-11-14 Andy Wingo <wingo@pobox.com>
* gst/playback/gstplaybin.c (gen_audio_element): Use autoaudiosink
as well if it is available. Fixes#316442.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_commit), (new_decoded_pad),
(setup_substreams), (set_active_source):
Unlock GROUP_LOCK in failure cases, so that we don't deadlock when
trying to go to NULL if we failed to read a file.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_init),
(gst_decode_bin_dispose), (free_dynamics), (remove_fakesink),
(pad_blocked), (close_pad_link), (new_pad), (no_more_pads):
Handle the case where a pad_block failed.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: (gst_decode_bin_init),
(gst_decode_bin_dispose), (free_dynamics), (pad_unblocked),
(pad_blocked), (close_pad_link), (new_pad):
Don't try to remove elements twice.
Original commit message from CVS:
* ext/vorbis/vorbisenc.c: (gst_vorbisenc_get_query_types),
(gst_vorbisenc_src_query):
Implement position and duration queries.
* gst/playback/test3.c: (update_scale), (main):
Fix for async state changes and print nicer output.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_destroy),
(gst_play_base_bin_change_state):
Fix leak.
Handle case where playbasebin is now ASYNC because
decodebin is.
Original commit message from CVS:
2005-10-16 Andy Wingo <wingo@pobox.com>
* gst/playback/gstdecodebin.c
(gst_element_set_state_like_a_crazy_man): New kraaaaaaazy
function!
(try_to_link_1): Increase kraziness level.
Original commit message from CVS:
* gst-libs/gst/audio/gstringbuffer.c: (gst_ring_buffer_commit),
(gst_ring_buffer_read), (gst_ring_buffer_clear):
Don't assert on normal stuff.
* gst/playback/gstplaybin.c: (do_playbin_seek):
API fix.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gst_play_bin_send_event_to_sink),
(do_playbin_seek), (gst_play_bin_send_event):
Override send_event differently, so that we can takes bits of
functionality from GstPipeline (special handling for seeks,
including pausing/resuming, and resetting stream time) and
still get
the appropriate behaviour of only forwarding event to a single
sink,
rather than all of them.
Unfortunately requires a lot of code duplication, but the
alternatives are equally ugly in the end.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (group_destroy),
(gen_preroll_element), (remove_groups), (setup_source):
* gst/playback/gstplaybin.c: (remove_sinks), (add_sink),
(setup_sinks), (gst_play_bin_send_event),
(gst_play_bin_change_state):
Set state to NULL before removing from bin. Fix refcounting.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gst_play_bin_send_event):
Correct refcounting in send_event() function. Previously was wrong
if the first sink was unable to handle the event.
Original commit message from CVS:
2005-10-03 Andy Wingo <wingo@pobox.com>
* gst/playback/gstdecodebin.c (try_to_link_1)
(remove_element_chain): set element to NULL before removing it.
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gst_play_bin_class_init),
(gst_play_bin_send_event):
Only seek on one sink, the first one that succeeds.
Original commit message from CVS:
2005-09-21 Andy Wingo <wingo@pobox.com>
* gst/playback/gstplaybasebin.c: Attempt to fix up buffer probe
thingies.
* gst/playback/gstdecodebin.c (gst_decode_bin_dispose): Dispose
can be called multiple times, dogs.
Original commit message from CVS:
* gst/playback/gstdecodebin.c: free plugin list correctly
* gst/playback/gstplaybin.c: emit warning if autovideosink
and autoaudiosink can't be found (instead of segfaulting)
Original commit message from CVS:
* check/generic/states.c:
* ext/ogg/gstoggdemux.c: (gst_ogg_pad_typefind):
* gst/playback/gstdecodebin.c: (gst_decode_bin_init):
Fixes for changes in registry API.
* configure.ac: Only export gst_plugins_desc. Add -no-undefined
to GST_PLUGIN_LDFLAGS.
* ext/libvisual/visual.c: Make the library shut up.
* gst-libs/gst/audio/audio.c: Don't define a plugin in a library.
* gst-libs/gst/audio/gstaudiofilter.c: same
Original commit message from CVS:
* gst/audioconvert/Makefile.am:
Audioconvert derives from GstBaseTransform and should
link to the library with our base elements to avoid
unresolved symbols. Makes things work with MinGW (#316160)
* gst/playback/test4.c: (main):
Fix MinGW build problem and use g_usleep() instead of
sleep() (#316162)
Original commit message from CVS:
* check/Makefile.am:
* configure.ac:
add core's plugins to the mix so that playbin works
* check/generic/states.c: (GST_START_TEST):
set a 0 timeout on pipelines, so they don't force the next
state change
* gst/playback/gstplaybasebin.c: (setup_source), (prepare_output),
(gst_play_base_bin_change_state):
remove the crappy error handling and do GST error handling
Original commit message from CVS:
* check/Makefile.am:
Add CHECK_CFLAGS and LDFLAGS
* gst/playback/gstplaybasebin.c: (fill_buffer):
GST_MESSAGE_SRC became a GObject
Original commit message from CVS:
* gst/playback/gstplaybin.c: (remove_sinks):
Remove visualization from parent explicitely; works around some
apparent refcount issue that I haven't tracked down yet.
Original commit message from CVS:
* common/gtk-doc-plugins.mak:
* docs/plugins/Makefile.am:
* docs/plugins/gst-plugins-base-plugins-docs.sgml:
* docs/plugins/gst-plugins-base-plugins-sections.txt:
renamed to actual element names, so much nicer to look at
* docs/plugins/tmpl/gstmultifdsink.sgml:
remove
* docs/plugins/tmpl/multifdsink.sgml:
* docs/plugins/tmpl/tcpserversink.sgml:
add
* ext/alsa/gstalsa.c:
* ext/cdparanoia/gstcdparanoia.c: (cdparanoia_get_property):
* ext/ogg/gstoggmux.c:
* gst/audioconvert/gstaudioconvert.c: (gst_audio_convert_chain):
* gst/playback/gstdecodebin.c:
* gst/tcp/gstmultifdsink.c: (gst_multifdsink_class_init):
* gst/tcp/gsttcpserversink.c:
various fixes and documentation additions
Original commit message from CVS:
* gst/playback/gstplaybin.c: (gen_video_element),
(gen_audio_element):
Switch to auto*sink elements as default sinks; add volume element
so that volume control in totem works.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (gen_preroll_element):
* gst/playback/gstplaybin.c: (setup_sinks),
(gst_play_bin_change_state):
Refcount fix and more comments.
Original commit message from CVS:
* gst/playback/gstplaybasebin.c: (fill_buffer):
Use _new_custom() so we can set custom message types for buffering
messages.
