Check that even if the subclass doesn't call set_output_format, the base
class should use upstream provided caps to fill the output caps that is
pushed before the gap event is forwarded, otherwise it ends again fixating
the rate and channels to 1.
https://bugzilla.gnome.org/show_bug.cgi?id=722144
For default caps generation when handling gap events that are sent
before any buffer, try to use caps that are closer to what upstream
provided to avoid fixating rate or channels to 1 as default.
So there are the steps:
1) Try to set rate, channels and channel-mask from upstream if provided
2) Fixate the rate and channels to the default rate and channels from
audio lib
3) Fixate the caps just to be sure everything is fixed
4) If no channel-mask was provided and channels > 2, use a default
channel-mask (taken from audioconvert code)
https://bugzilla.gnome.org/show_bug.cgi?id=722144
A xvcontext can be created early in gst_xvimagesink_set_window_handle().
In this case don't recreate, i.e. overwrite it in gst_xvimagesink_open().
Otherwise XEvents won't be handled in the xevent listener thread.
Fixes a regression when setting the window handle on the sink in
the very beginning before changing its state.
https://bugzilla.gnome.org/show_bug.cgi?id=715138
A change in gst_ogg_demux_do_seek caused oggdemux to wait for
a page for each of the streams, including a skeleton stream if
one was present. Since Skeleton only has header pages, that
was never going to end well.
Also, the code was skipping CMML streams when looking for pages,
so would also have broken on CMML streams.
Thus, we change the code to disregard Skeleton streams, as well
as discontinuous streams (such as CMML and Kate). While it may
be desirable to consider Kate streams too (in order to avoid
losing a subtitle starting near the seek point), this may be
a performance drag when seeking where no subtitles are. Maybe
one could add a "give up" threshold for such discontinuous
streams, so we'd get any page if there is one, but do not end
up reading preposterous amounts of data otherwise.
In any case, it is important that the code that determines
the amount of streams to look pages for remains consistent with
the "early out" conditions of the code that actually parses
the incoming pages, lest we never decrease the pending counter
to zero.
This fixes seeking on a file with a skeleton track reading all
the file on each seek.
https://bugzilla.gnome.org/show_bug.cgi?id=719615
Ogg data is read chunk by chunk, and the chunk size used was
originally taken from libvorbisfile. However, this value leads
to poor performance when used on an Ogg file with large pages
(Ogg pages can be close to 64 KB).
We can't just use a larger chunk size, since this will decrease
performance on small page streams, so we use an adaptive scheme
where the chunk size is twice the largest page size we've seen
so far in the stream. For "typical" Ogg/Vorbis, this gives us
almost the same chunk size (a bit lower), and this lets us get
better performance on streams with large pages.
Before trying to generate a default fixated caps when handling a gap
event, make sure that the same strategy that is used when handling
a buffer has been attempted. Otherwise audiodecoder will ignore
upstream caps settings such as rate and channels and will likely
end with a caps with channels=1 and rate=1.
https://bugzilla.gnome.org/show_bug.cgi?id=722144
Don't try to interpolate the chroma samples, the used algorithm only
works for horizontal cositing. Let's switch to a faster and safer
version until we handle chroma siting correctly in the fastpaths.
Instead of using extra plane, we encode the number of tiles in x and y in the stride of
each planes (i.e. y_tiles << 16 | x_tiles) and introduce tile_mode, tile_width and
tile_height into GstVideoFormatInfo structure.
https://bugzilla.gnome.org/show_bug.cgi?id=707361
Adds a test that simulates a scenario where the first buffers after
a segment can't be decoded and the decoder asks for those frames
to be released. The videodecoder base class should make sure that
the events attached to those first buffers are pushed even if the
buffers aren't going to be.
https://bugzilla.gnome.org/show_bug.cgi?id=721835
For reverse playback, the segment event will only be pushed when
the first buffer is actually pushed. But for decoding frames and storing
those into the list to be pushed the output_segment.rate value is used
to determine if it is forward or reverse playback.
In case a previous segment event (or none) is in use it will mistakenly
think it is doing forward playback and push the buffers immediatelly and
try to clip buffers based on an old segment (or an uninitialized one, leading
to an assertion)
This patch fixes this by copying the segment earlier if on reverse playback
https://bugzilla.gnome.org/show_bug.cgi?id=721666
Rework the orc code to be around 10% faster and support arbitrary matrices.
Pass the matrix parameters to the YUV->RGB functions to make them work
for all matrices. This enables more and faster fastpath conversions.
See https://bugzilla.gnome.org/show_bug.cgi?id=721701
Add a simple playback test that makes sure that video decoder pushes
buffers in the same order it receives and that it respects the
set timestamps and durations
